Jump to content
Sarge

D-180 hydro steel manifold o-rings

Recommended Posts

Sarge

I know in the past someone posted up the sizes/numbers for the o-rings that fit between the hydro pump and the steel lines' manifold blocks on the D-series - I'd imagine the ones at the pump end and rear axle are the same ....?

Will be changing my pump soon due to the hydro to engine coupler blew out it's splines and took out the shaft along with it . Evidently a trailer weighing around 2.5 tons was too much....

 

I'll try to write up a post on how to build a new coupler from a later model C series pump pulley's center ring and a worn D coupler as well - trying to finish up the Ross steering box right now .

 

5960d59ed9429_20170702_1443251.jpg.48ae30704a5ac45cbd4a99d1d8c1cc24.jpg

 

 

 

Sarge

Share this post


Link to post
Share on other sites
 
pfrederi

Dash #018 (larger ring)

Dash #015 smaller

 

The Backer ring is also a Dash 018.

 

Also need a crush/sealing washer 1/2"  for teh back end.

 

I have all of them and can mail you a set PM your address.

 

Can't wait to see your coupling fix

Edited by pfrederi
  • Thanks 1

Share this post


Link to post
Share on other sites
 
Sarge

The coupling fix will require some lathe work at minimum and possibly have to do some of the cutting on a mill . Not an easy fix , but it's known to far stronger than the original setup and far less prone to wear over time . I've searched until I couldn't see anymore trying to find a short and more modern coupler design that could work - came up with nothing at all due to the length of space available . If it were off the pto side of the big twin - that would be easy . Flywheel side ....not so much and moving either the pump or the engine is out of the question unless you want a tractor that is useless .

 

Message sent , sure appreciate the help .

 

Sarge

Share this post


Link to post
Share on other sites
 
DavidP

@pfrederi

I know this is an old post but do you still have any extra sets that I could buy from you?

I would take 2-3 sets if you have them.

Share this post


Link to post
Share on other sites
 
pfrederi

PM me your address I will send you some free.

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • BuffaloD200
      By BuffaloD200
      Hey all, 
       
      My '74 D180 has a lot of trouble pushing snow.  Weighted tires, but nothing else at this time.  I've found it gets stuck frequently and only one wheel spins.  Do these tractors not have a limited slip/locker arrangement?  How does everyone manage with the infamous one wheel peel?
    • BuffaloD200
      By BuffaloD200
      Hey all, I need to install a drive belt on my 75 D180 for my snowblower.  I've looked through a bunch of D-series owner's manuals, and none seem to mention replacement procedure.  The PTO pulley is fixed, save for engaging the PTO and there is minimal movement at the snowthrower pulley. There's no idler or tensioner as far as I can tell.  Do I have to remove the PTO pulley?  That seems to be a required service item.
      Same question for my 80 D200 as well really.  
       
      Using the recommended 4L490W belt.
       
      Thanks 
    • Redtickuleez
      By Redtickuleez
      Hello gentlemen!!! I recently bought a d180 with loader and backhoe. Im looking for serial number.. there is a plate under the steering wheel but its been pajnted over and i can make it out. Can y'all tell me another location and was this tractor pruchased originally with these attachments and any info would be greatly appreciated... Thanks fellow Wheel Horse enthusiasts !!! !! !!!
    • ihatephones
      By ihatephones
      I got a D-180 for $250, and the governor is messed up, the points won't open or close, and I took it apart and was being stupid and messed some stuff up in there, and now I need a new one.
      Where can I get one that's not on eBay for $200?
      I also forgot to say it was a Kohler K482, and I'll throw some pictures of the tractor in as a treat.


    • Southern_Secret
      By Southern_Secret
      Hello fellow Horse Heads long time no post for me, life gets crazy & a lot of things change sometimes but anyhoo. So back a few years ago when I first got my 1994 314-H I had it at my shop going threw it. One of my customers walk past as im working and said, you know I think Iv got a Wheel Horse & im thinking "no you dont buddy". I give him my # to send pics thinking it was a big waste of time & after getting the pics I realized he did have a Wheel Horse! I hand shake bought it right there, asked him to bring it to my store & he said no problem. Well after almost 2 years it is finally in my orbit. I know very little about it other than his father-inlaw got it new and used it around his house moving snow and stuff. His father inlaw moved down south here when his daughter got married and gave the tractor to my customer because he had a farm & his the inlaw had no use for it anymore. Same with every barn find, "it was running when parked" 8 years ago, said one of the axel seal is leaking. Im happy and hope I can get it back in running order soon cause it is going to be handy around the truck farm!!
       
      I will post Pics as soon as I reinstate my membership





×
×
  • Create New...