Leaderboard

So I'm down to two Black hoods after my A-60 started it's way to Wisconsin... And, well there's this B-80 pops up on MP for $50. Motor and trans are free, tires all have air, seat is to die for... so, Here's the obligatory pics and what I've done so far: Carb dip - 3 times New battery New battery cables Motor oil change (bad) Trans oil change (really bad) New fuel line and filter Fresh rec gas New air filter Mouse house removal She runs, but still getting some surging... Still on the plate: Dial in the carb / fix surge issue Tires are tired... Grease Tie rods Rewire lights I'm sure something else will pop up... My C-125 is currently set up as a plow mule and back up snow machine. Not sure if this B-80 would be better suited to snow or mule duties... IMG_4279.mov

So the folks working on my house cleaned up most of the debris from the fire. That being said there is alot of small stuff everywhere. Siding, drywall, burnt pieces of lumber, and whatever else you can imagine. Of course this makes mowing a bit of a challenge. So I bought something to drag around and pick it up. Not to mention it will help smooth some of the ruts left by heavy equipment. At least to the point they won't snag the mower deck. I'll report back how it works later this evening.

I adjusted the lift links. It sits about 4 inches off the ground now. No not really. It's not "60 inch mower deck heavy", but you know it's there for sure. I'm gonna add another hole in the hitch to slide it forward. It has a radiant for rotating to both sides but it won't get used that way here. I think that will lighten the leveraged load a bit on the lift arm. First test was the gravel driveway. Got rid of the studder bumps on the first pass. So far so good.

Split some wood today and the C-121 was on log splitter hauling duty.

September 15, 1962, Frankie Valli and the Four Seasons' "Sherry" hits the top of the pop music charts. It was the start of a remarkable run of hits. Valli (born Francis Casteluccio) had been hard at work trying to become a star for the better part of a decade before the Four Seasons achieved their breakthrough. They had come together as a group in several stages over the previous four years, changing their name in 1961 from the Four Lovers after failing an audition at a New Jersey bowling alley called The Four Seasons.

953/1054's are a fun project. Before/After attached.

I learned this afternoon that Paul Benzinger (oldredrider) passed away the week before last. I talked to his wife, who told me he had been battling cancer for quite a while, and gave me the okay to pass the word along to RedSquare. I didn't know Paul well, only really met him once, at the big show in 2021. We talked about the engines he had rebuilt and had for sale at the show, and generally just had a real easy conversation about Wheel Horses and Kohlers, and just life. I know some of you guys knew him much better, and I'm looking forward to hearing some of your stories. Rest in peace, Paul, and thanks for the chat. @nylyon

I built one like that a few years ago, love it.

B-80 would make a fine plow mule with that 8" Brinly you have. I wouldn't even think twice about throwing a ten on. Heck maybe even a 12 just for a hold my beer and watch this. Guessing you would run out of traction before power in hard dirt. I had a no name eight that was a house mule and it did just fine.

I bought a lift table from Harbor Freight years ago, one of the best tools ever made for us old codgers.

On a rural road, a state trooper pulled a farmer over and said, “Sir, do you realize your wife fell out of the car several miles back?” To which the farmer replied: “Thank God, I thought I had gone deaf!”

Hold my beer and watch this.

Picked up some HEAVY Bolens front cast iron weights. They had "BOLENS" cast into the face, so I filled them with some JB Weld. Decided while I was painting them, that my JD rear weights needed to be red too! Now all my iron weights are red. Just one set of plastic fronts are the odd-balls now. Started doing a little prep work for an upcoming parade in our local festival.

He was a long time member here on RedSquare @oldredrider rest in peace!

Yes, it is two bolts holding the base. Also two fittings for the inlet and outlet oil lines. Both lines (on our tractor) are metal tubing so you cannot count on much movement. If I were to tackle this, I’d remove the seat, fender, left rear tire, the fuel tank, and any other bits in the way to get easier access. Lastly, remember that the oil in this system circulates in the hydro pump and motor. Any dirt or contaminant entering the system could cause damage so a through cleaning before cracking open the oil line or filter is the wise move and keeping the work area clean is the best practice.

Head bolts painted. Engine lifting strap painted. Valve cover assembly removed.

I could take it off your hands for you and that would fix your problem

Can't hurt... expired in 2017, so either use it for bicycles chain oil or put it on the deck and see what happens...

Weight is traction. Putt Putt has pulled plenty of 10” and 12” plows, and has a much smaller belt contact patch. Just add weight. And tires. And more weight. @Blasterdad shows up with a B-80 and plows all day.

Use it or lose it!

Not sure this is good for the deck though.... KEVIN!!! https://www.facebook.com/reel/2833060297040424

Interesting assist torsion spring return thingy on the Clutch pedal - is there a heavy spring in the OE position too? (or was this a PO backyard "fix") If that's it, there may not be enough force to keep the drivebelt tight enough...

Item #38 https://www.partstree.com/models/95-48xs00-toro-48-side-discharge-mower-deck-1979/side-discharge-mower-48-in-122-cm-vehicle-identification-numbers-85-48xs01-95-48xs00-3-11/

Very nice!!! 👍👍👍👍

Was fortunate enough to be first in line to get this on the weekend. Good shape - light surface rust only - PO said stored inside. Tires all hold air although showing their age. Really good score. Is this a model UW-643 or the 7-2211 The only way to tell is by the decal style. There is no serial number plate. And what's the deal with that decal. I could count on one hand the number of times I've seen it.

My suspicion is when you arced the rush of power broke down a sheet metal to sheet metal contact point in the ground path that was somewhat corroded anyway.

Hallelujah. My persistence paid off and all your help she runs again!! Took ground from battery to engine mount and she's alive! From the mower graveyard given new life then I killed her and brought her back to life again haha 😄

Why did the lamb call the police? He had been fleeced.

Cylinder head removed. Cylinder head bead blasted. Head bolts as removed. Head bolts bead blasted. Head bolts ready for paint. Head bolt washers as removed. These are not cleaned up as I have new hardened washers to install. Engine with head removed. There is very little carbon buildup or obvious wear.

Excellent harmony to follow the voice of the lead singer. Days gone by...

It would never break under an S-10, but it is a good bit wider. The 8.8 can be had in S-10 is width with the same 31-spline components an f-150 got.

You came to the wrong place if you’re asking for advice on that! These guys are a bunch of enablers 🤣🤣🤣

Change a couple of pulleys and maybe a belt, and “awaaaaaay we go!” (NOT to the moon) (Only saw the first two frames of the FB post since I’m not a member!)

With the modern PT we were told to expect replacement of the deck between 7 and 10 years - or less. Maybe this ATV guy is on to something protecting his deck with a coating of rubber.

Now you have given @Pullstart some more ideas he didn't need.

RIP Red Rider.

Fer sure although the 1054 isn't bad on fuel. I take her to WFOT and then just back it off a bit and running in 2nd. not a speed demon but gets the job done. @PeacemakerJack always said it all depends on the soil and conditions with small bore singles. That's why the MN boys run heavy weighted 16s. They are good to go for any soil type.

Yes PO POS...! yes it works, yes it's unique, not enough pressure so no it ain't staying... I have a bunch of trampoline springs I've used on previous projects - as @Pullstart knows... it's on the list...

Like going to the Gym every time you stop!

@SylvanLakeWH Get you a 108035 and maybe even add some to that on the inside. I have a couple tractors with double springs.

I can't speak for the dirt plow dogs but B80 is a great snow plow rig.

Neeeaaat

There is a member on here, @953 nut who always says, CHECK THE GROUNDS FIRST. Good advice.

Why was the cucumber mad? Because it was in a pickle! How did the farmer find his lost cow? He tractor down.

To ensure proper lubrication and cooling a working Wheel Horse, it should be run at WOT (wide open throttle. The foot throttle on my dragster was not a working tractor. It was designed for show, wheel stands, speed, and speed shifting without using the clutch.