Leaderboard

This will be my last build. As you can se up to this point it is a lot of work doing it this way But the end result is very nice looking tractor. I hope you enjoy the video.

Well guys I'm all packed up and the wheel horse cart, C-81 and suburban are stuffed in the box truck, ranger and 753 will be coming down Sunday on my second trip down. Oo and my kids + niece were spending there last days together for awhile so they posed with the tractors for a good bye picture!

Met a man at a gas station on my way home from a show. He was checking out my Horses and asked if I was interested in some engines. Never discussed a price but I was curious so I stopped by his house to night to see what he had. Turns out he had 2 K181's and some Briggs engines after I picked what I wanted he's said "enjoy" and wouldn't take any money. Tried arguing this fact but he would have nothing to do with it. All 4 engines turn over and are complete

Hey guys... Tonight was the night. I opened the fuel valve, sprayed a couple shots of starter fluid into the air intake, and turned the key. It fired right up. A couple more shots of starter fluid and it was running on its own. Pulled the throttle in and out a few times and it responded perfectly. I pushed the hydro lever into reverse to test the trans and I got nothing. Moved it forward and got nothin. I was just about to get upset that it wasn't working when I thought I better check the parking brake. Yep, it was engaged. What relief. Now to complete the final assembly and the finishing touches/touch ups.

I used a Gardner Spring #37083GS from McMaster-Carr. Their number is 9433K111. I actually ordered them for the PTO on my 500 Special and found that they are a close match for the clutch spring on my Suburban 400. Another plus for me is that they are stainless steel.

Could always take it to these guys... Seriously check the local car & motorcycle shops they may do stuff like that or more important knows some one that does in your area.

Used my Toro Wheelhorse 12-32XL to hide my Seadoos in the backyard in prep for storm HERMINE.

There is a new Wheel Horser on the way!

Welcome aboard . Perhaps you could mock up a piece of 1/4" flat plate using the existing hole for an anchor point & butt it up to the backside for when you're stopping . Looks like it's chewing the heck out of that rear pan . If it's for light duty only . Just a thought .

Wheel Horse # 1014 spring replaced by 83-2730 4.500" between hooks, .070" wire, .520" coil OD, .380 coil ID, 3.570" coil length, 52 + 2 half coils Garry

On line catalogs; desk top, lap top, I pad or Smart phone? That could be messy!

Ha, I know nothing!!!!!!!!!!!!!! but certain things I'm comfortable with. If it was 6000 lbs with someone working underneath it, get an engineer! But carrying 300 lbs at 7 mph, Duct tape and vice grips will hold that. LoL Don't worry too much about that brace, not that much structure to it unless you're carrying 600 lbs and bouncing full speed through some ruts for a 100 yards. It definitely has a purpose but it's made the easiest way, located in the easiest spot for manufacturing and it looks good there. Moving it a little will not compromise it's purpose IMO.

The early hydrostatic transmissions used "dynamic" braking. Neutral is your brake. It will have a parking brake that locks a gear inside the tranny.

9-1-1968 Clown College opens Clown College was the brainchild of Irvin Feld, the owner of Ringling Bros. and Barnum & Bailey Circus, and longtime Ringling clown and front man Bill Ballantine. In 1968, Ringling had only a handful of clowns in their alleys, most of them over fifty years of age. It was clear that these performers wouldn't be able to go on forever. But there was a dearth of suitable replacements at that time. So Feld decided to create a school to train a new generation in this ancient art form. Feld also saw the potential public relations opportunity in having a place that could become the Mecca of clowning in America. In addition, he wanted to use the school as another way of keeping his show more attractive to audiences than his competition, and have a place where he could guarantee getting an endless supply of new talent. In 1984, after Feld's death, Kenneth Feld, his son, took over production of Feld Entertainment and the Ringling shows. He continued to operate the school through the 1997 session, and then closed Clown College because the needs of the show had changed. The school was no longer profitable, nor necessary, as clowning had moved back into the mainstream of performing arts. Also, with nearly fifteen hundred graduates, many of whom were teaching others the lessons they had learned, and with a home videotape produced by Ringling and made at Clown College in 1986 titled "Be A Clown," which featured many of the techniques used in the school's training sessions, Ringling Bros and Barnum & Bailey Circus officially discontinued their Clown College just shy of its 30th year. Currently, clowns for the Ringling shows are hired based on standard auditions, much like any theatrical production. After 25 years the college moved from Venice, FL to Baraboo, Wisconsin, hometown of the Ringling Bros. After three years in Baraboo the college moved to Sarasota where it was based for two years, closing after the graduation of the 1997 class.

HAPPY SEPTEMBER EVERYONE.

I think we`ve got a few graduates on this site....

This is the pathway current would need to follow to get from the hood support to the engine and then the starter. paint over any one of the connections between the body panels and you lose ground to your block

I'll take a stab at it .... A T-Rex eating a prawn .

Besides driving the tractor on the highway, the most useful and enjoyable thing a party hardy red neck can do is get the ironing board that we all have stored in the closet behind the 12 gauge double barrel shotgun out and get it ready for the holidays....... no turkey emoticons??? Here are just a few ideas....... I always ask the relatives to bring their own ironing boards and beer and sleeping bags, bed roll or cot as well. The out house is always fully stocked with Sears and JC Penney catalogs. And if the indians set the telephone poles on fire, get ready for a great old time!!! Bring the camera!

Looking at your photo The red wires go to the 2 terminals farthest apart at the top for the starter circuit There are 2 black wires going to each terminal that are closest together in the bottom row for the ignition circuit Garry Adding This 105303 connector fits this switch and still available from Toro https://www.partstree.com/parts/toro/parts/105303/

Don't think it's going to make any difference but it will change the RPMs a bit. My factory pump is lined up with the inner pulley with all the factory brackets. MISTAKE --- My factory pump is on the outer pulley too. Backhoe pump on the inner pulley. Still don't think it matters much especially if you need the room.

As oldredrider said the transmission performs the braking function; on the right side down low you have a parking brake but chances are it has failed to function years ago (not the best engineering) I use the bucket of the FEL as my parking brake.

Don't worry Bob...sounds like 'fish knows a thing or two about structural Or does he?? 'Sides when you are challenged in the art of joining metals via electricity a project such as this can be difficult...ask me how I know!

Thanks Walt. I already explained my thoughts and differences between the hoarding vs. collecting, and I believe I'm a collector although it doesn't appear that way from the pictures! A. I should have a second barn, however it's not due to wanting more tractors. It's for my sleeping arrangements if I find myself buying another tractor. At least that's what she's threatening anyhow. B. No worries about the scarceness of Wheel Horse's or parts, as I'm not planning on starting a collection of Wheel Horse's anytime soon. If I do however, I will give you guys plenty of notice before hand! C. If you are wanting to invest, then put all your money on Tallmans Ag. Paint, as they are the only paint manufacturer that I'll use. Be sure to put 50% in the John Deere Green shade and the other 50% in the John Deere Yellow shade.

Shamu sticking his tounge out.

Good lord man! Lyme can present in SO many ways! We've had dogs with it so I know it's around. Even thought I had it once but the test was negative. Got bit twice this spring but no further issues... Hope you get rid if it and all the symptoms! Very scary disease!

Here's a quick drawing, No welding necessary. The brace should probably be slotted to adjust belt tension. main pump plate 3/16 or 1/4" flat bar. Might not have to be as wide if you drill pump mount holes vertical instead of horizontal

Bring in the clowns.

Welcome to the Machine Thought I would post up some recent modifications to The Machine prior to up coming plow season. After a good season of plowing last year it was time for some upgrades, not because what I had did not work, just wanted try to make it better. So I started with some new Firestone 16-6.5-8 tri ribs, and 23-10.5-12 23 degree bar tires, added an 1054 hy pump, with new seals and spring, welded cylinder rebuild with new hyd lines and lift cable and adjustable tie rods from @wheelhorseman1000. Also ordered up a 12" shear and moleboard from Brinly, and to hold the front end found an old cub that needed to be squashed for the weight on the from to hold all them ponies down. 5th( don't know how it moved it was 1st) picture is last years, all others are with modifications. Bring on plowing season.

How much actually went on the tractor Bob...

Thanks guys! You are all awesome!! Almost to Cleveland now..

For got to post this pic of dueling steam engines doing a spark show. The one on the left is a Nichols & Shepard, the one on the right is a 2/3 scale Case.

Lots of great vintage tin there! You done Good.

Richard!

I'm never that lucky but would you mind if others (who shall remain nameless) might use parts of that same story. I mean it could help explain a few new wheel horse purchases if you know what I mean... Thanks in advance

The top view of your transaxle tells me it is the early Sundstrand 3100077 found on the 10/1277, not the 90-2046 found on '68 and later. The 90-2046 has the tow valve on the top,yours does not. I guess it could have been a 10/1276 also, who cares, it is still a great worker.

That only works if you put the chair on top of the board! It doesn't work the other way around!

hi all, here's a link to a slide show i got from a guy i play videogames and talk tractors with he apologizes for the few blurry photos http://s1346.photobucket.com/g00//user/Jakalth/slideshow/pioneer power show

Thats a good deal for 700 maybe you could offer him 600. The engine is a great engine, they go forever and parts and attachments are everywhere for it. Thanks, dave

I could use your advice about buying this tractor

Can any one tell me the best place / site to advertise or sell a wheel horse tractor?

1227 roll pin is 3/16" x 1-3/4". Have in my notes the length may be 1-3/8" but measure the hub diameter to be sure and let us know. Garry

Nice job. And I hear you about getting to that point in your life where you don't need all the tractors. I haven't started some of mine in over a year. That's why it's time for them to go. You never know. The time may come around again when I get the "itch" and i'll probably start over again. But if I do, I will be a little wiser in what i'm looking for and what I want to start with.

Mine is on the outer pulley, and I`m sure it`s factory..

if theres any you don't want feel free to send them my way nothing better then free

I thought it was the loch ness monster on land Horse 46........

Randy, looks to be a 67 or 68. There should be a tag riveted under the dash on the hood stand. The holes are there but sadly it appears the tag is missing. Tag off the engine will help but others will be along to help ID it. Guys around here seem to get off on identifing horses. Once we know what it is for sure all the manuals can be found here.

VETERANS ...... THANK YOU for your Service!!