Jump to content
ebinmaine

657/867/1267 clutch idler pulley?

Recommended Posts

ebinmaine
Posted (edited)

@OldWorkHorse Steve and I both need a clutch idler pulley on early tractors. 

 

The one from Trina's 856 military tribute tractor measures 3" od. 

 

How do we get these new?

 

Is there a Sten's or other aftermarket number?

 

Edited by ebinmaine
  • Like 2

Share this post


Link to post
Share on other sites
 
stevasaurus

Well Eric, you could try our "Classified / Wanted" Section.  A-Z, etc.  :occasion-xmas:

  • Like 2
  • Thanks 1

Share this post


Link to post
Share on other sites
 
ebinmaine
4 minutes ago, stevasaurus said:

Well Eric, you could try our "Classified / Wanted" Section.  A-Z, etc.  :occasion-xmas:

😀

 

Oh.. I know.  

In fact Lincoln was my first thought.

 

I'll edit my first post. I was hoping for a part number from some place like Sten's or an alternate source for new ones.

 

I need one and I want to put one in stock and I know Steve needs one too. 

 

  • Like 2

Share this post


Link to post
Share on other sites
 
Pollack Pete

Anything at Tractor Supply? I've seen various pulleys there.Just a thought.

  • Like 3

Share this post


Link to post
Share on other sites
 
squonk
30 minutes ago, ebinmaine said:

@OldWorkHorse Steve and I both need a clutch idler pulley on early tractors. 

 

The one from Trina's 856 military tribute tractor measures 3" od. 

 

How do we get these new?

 

Is there a Sten's or other aftermarket number?

 

Eric, PM @prondzy

  • Thanks 1

Share this post


Link to post
Share on other sites
 
elcamino/wheelhorse

@ebinmaine Try K & B just bought 2 deck idler pulleys from him.  There was a guy on here a couple of years ago that had a boat load of pulleys for sale. You may want to do a search.

  • Like 1
  • Thanks 2

Share this post


Link to post
Share on other sites
 
EricF
16 minutes ago, Pollack Pete said:

Anything at Tractor Supply? I've seen various pulleys there.Just a thought.

I was able to track down a pulley for a Bolens deck at TSC a while back. Correct pulley diameter and shaft size, but the overall thickness of the pulley due to heavier-gauge metal made it too thick to put the top shroud back on over it; had to run it exposed. May or may not be an issue for you; check your clearances under the belt shroud if you think they have a match.

  • Like 2

Share this post


Link to post
Share on other sites
 
stevasaurus

Waldo, I remember seeing all those pulleys that guy had...they were Wheel Horse pulleys also.  Right, about 2 years ago in the For Sale Classifieds.  :occasion-xmas:

  • Like 3

Share this post


Link to post
Share on other sites
 
squonk

@prondzy rebuilds them.

  • Like 3
  • Heart 1

Share this post


Link to post
Share on other sites
 
oliver2-44

I got some rebuilt by Prodzy. Very 👍🏾 

  • Like 4
  • Heart 1

Share this post


Link to post
Share on other sites
 
Pollack Pete

Just tried a Google search for 3 in. OD idler pulley.Lots there.What size center hole do you need?

  • Like 3

Share this post


Link to post
Share on other sites
 
pfrederi
Posted (edited)

867 use pulley 1623 now 92-7102 only $45

Edited by pfrederi
  • Like 1

Share this post


Link to post
Share on other sites
 
ebinmaine
Posted (edited)
14 minutes ago, pfrederi said:

867 use pulley 1623 now 92-7102 only $45

"Only".....

I don't mind spending money on something when I need to but I'm too damn cheap to spend $45 on a pulley...

 

Between Steve and I we need 4. 

Edited by ebinmaine
  • Like 1
  • Haha 1

Share this post


Link to post
Share on other sites
 
ebinmaine
58 minutes ago, Pollack Pete said:

Just tried a Google search for 3 in. OD idler pulley.Lots there.What size center hole do you need?

Thanks Pete. I'll check it out when I get home. I think it's 3/8?

 

Looks likely that we'll order four of them from @prondzy

  • Like 1

Share this post


Link to post
Share on other sites
 
ebinmaine
1 hour ago, stevasaurus said:

Waldo, I remember seeing all those pulleys that guy had...they were Wheel Horse pulleys also.  Right, about 2 years ago in the For Sale Classifieds.  :occasion-xmas:

Steve I looked on my phone which is of course different from a pc. My listings using a search term "pulley or pulleys" only go back maybe six or seven months? I couldn't figure out how to go any further than that.

 

Share this post


Link to post
Share on other sites
 
elcamino/wheelhorse

@stevasaurus It was about 2 plus years ago.

  • Like 1

Share this post


Link to post
Share on other sites
 
rjg854

@greenbushtrees I think was his handle. I've bought a few different pulleys from him over the years. I don't think I've ever seen him post much.

  • Like 2

Share this post


Link to post
Share on other sites
 
daveoman1966
Posted (edited)

I have an ebay listing with the 1623 pulley.    I have TWO of these...$21.95 each + 5 ship.  

Ebay item 133412177681

 

 

015.JPG

014.JPG

V idler A (3).JPG

V idler A (4).JPG

Edited by daveoman1966
  • Like 3
  • Thanks 2

Share this post


Link to post
Share on other sites
 
kpinnc
Posted (edited)

I got one today at TSC for $19. 3 inch diameter with a 3/8 bearing. It will need a spacer on the mounting bolt, but that is easy enough.

Edited by kpinnc
  • Excellent 1

Share this post


Link to post
Share on other sites
 
ebinmaine
6 hours ago, kpinnc said:

I got one today at TSC for $19. 3 inch diameter with a 3/8 bearing. It will need a spacer on the mounting bolt, but that is easy enough.

Could you post pics please?

 

  • Excellent 1

Share this post


Link to post
Share on other sites
 
kpinnc
Posted (edited)
13 hours ago, ebinmaine said:

Could you post pics please?

I typoed that, it is 5/8 bore. I think the spacers are 3/4 but they have that size at TSC too.

IMG_20210502_150057308.jpg

Edited by kpinnc
  • Thanks 1

Share this post


Link to post
Share on other sites
 
ebinmaine
1 hour ago, kpinnc said:

I typoed that, it is 5/8 bore. I think the spacers are 3/4 but they have that size at TSC too.

IMG_20210502_150057308.jpg

@OldWorkHorse

Steve lookitt here. 

  • Excellent 1

Share this post


Link to post
Share on other sites
 
OldWorkHorse

If I get a min ill swing by there today and see what I can find. Got to go the metal place to and we know what happened last time I went to TSC and the metal store all in one day...

  • Haha 1

Share this post


Link to post
Share on other sites
 
Howie

I always press the insert out of a wornout pulley and save them. A lot of them

have that bearing and an insert pressed into it. Sometimes have to shorten the

back side for alignment.

  • Like 1

Share this post


Link to post
Share on other sites
 
Lane Ranger
On 4/30/2021 at 2:23 PM, squonk said:

@prondzy rebuilds them.


 

I have had several rebuilt by @prondzy and you can’t beat his price and quality of work.  I save every old original 1623 riveted idler pulley.   Going to send them to Mike for rebuilds!   

  • Like 1

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...