Custom 3d printed badges, ornaments etc.

[Wheel Horse 3D 3,622]

So here are our first 3 reds in the same left to right order.

[Wheel Horse 3D 3,622]

1/32 gas station island and light fixture

Modeled after those at very first HESS station in 1960

[Wheel Horse 3D 3,622]

[Wheel Horse 3D 3,622]

Ok here we have left to right

Original(mug handle), signal red(pendant), and our enzo red(failed keyfob)

[Wheel Horse 3D 3,622]

Thinking enzos gonna work! Still not perfect but everything about it says red, nit orange, not pink lol

Edited April 27, 2021 by Wheel Horse 3D

[Wheel Horse 3D 3,622]

As another test, here it is with a swatch of testors red gloss enamel painted on.

[rjg854 10,748]

I think you're on to something 

[Wheel Horse 3D 3,622]

Ok, heres a question for all the WH ladies out there..if one was to wear a WH pendant, how would you prefer the ring to face?

Mrs 3D would prefer the ring to face the same as the keyfob, so a cord could be looped through the ring and "cats paw" to the pendant, and the pendant doesnt slide on the cord. My initial thoughts were pendant would go an whatever cord or necklace and could float freely while still laying flat.

 

Soooo..should we leave the pendant as is..or turn the ring so its just like the keyfob?

[ebinmaine 63,214]

3 hours ago, Wheel Horse 3D said:

leave the pendant as is

We're not much for wearing necklaces but that's the way I'd vote to put it. That way it can slide freely and not get twisted up.

 

[Wheel Horse 3D 3,622]

Whole run if enzo red keyfobs and pendants..up next..."silver dollar" keyfobs and pendants

Edited April 28, 2021 by Wheel Horse 3D

[Wheel Horse 3D 3,622]

Heres  the silver up against my blue/gray prototyping filament

[ebinmaine 63,214]

Quite a difference

[Wheel Horse 3D 3,622]

Todays tinkering...modify the Quart size jar stein with the zip tie pockets, beef up the lid a little thicker, and display in #EC1207 enzo red(or as close as this monitor can get) ..ready for a print! Will likely still paint the hood ornament base portion in silver, but all else stays red other than the topper.

[Wheel Horse 3D 3,622]

Those little plastic tie rod end caps????

 

When I was cleaning on Dug the other day, I noted a loose piece of quite thin plastic on the end of his steering rod that pushes on the end of the rod and is supposed to snap around the shaft of the ball. Think you can just see it there just behind the left front tire.

Edited April 28, 2021 by Wheel Horse 3D

[Wheel Horse 3D 3,622]

Silver run of keyfobs and pendants came out good. Im pretty pleased.The silver reflects the light nicely from different angles, and is right on for a silver crayola.

 

 

[ebinmaine 63,214]

5 minutes ago, Wheel Horse 3D said:

silver

Might do to remember that color for tools and garage accessories.  

[ebinmaine 63,214]

1 hour ago, Wheel Horse 3D said:

plastic tie rod end caps

Good for shielding from rain but they hold dust blown up into them. 

[Wheel Horse 3D 3,622]

2 hours ago, ebinmaine said:

Good for shielding from rain but they hold dust blown up into them. 

Well since Dug and I both prefer not to work in the rain....! Dont think we'll bother with that!

[Wheel Horse 3D 3,622]

A little snip of how my evening goes...assembly of a Wheel Horse 3d/Classic keyfob in silver.

 

[Wheel Horse 3D 3,622]

Workin on an led ornament for Dug...once finished with the black, im thinking the spokes, hub, and rim in white

[Wheel Horse 3D 3,622]

Todays tinkering...pallet jack and BIG wrenches and sockets, 5ft pry bar, and a big 24"pipe wrench.

[Wheel Horse 3D 3,622]

WH   Der Jar Stein in enzo red.

[Wheel Horse 3D 3,622]

Still pondering priority of items for Big Show.

Thinking at the moment the direct replacement stuff should be priority.(headlight lenses, ornaments) so right now Im workin a few batches of those.

Edited April 30, 2021 by Wheel Horse 3D

[Wheel Horse 3D 3,622]

Man these are tedious! Lol  one down!

[Wheel Horse 3D 3,622]

Or we can get REALLY tedious....think im gonna put this on Dug!