Jump to content

So... now in confused

Recommended Posts


I had a drive belt let go on a 1980 C-175 Sundstrand hydro. After searching the manuals it looks like either an 83" or an 85 1/2" belt is called for. 

Anyone know the right length off the top of their head?


Share this post

Link to post
Share on other sites

Transmission drive belt 106496 - (HB x 85.60" or 5/8" x 85.6")



  • Like 2

Share this post

Link to post
Share on other sites
953 nut

Conventional belt size would be 5L-850 or B-82. I have had good luck with the Kevlar Belts from Tractor Supply.

  • Like 2

Share this post

Link to post
Share on other sites

Thanks guys.

Appreciate the help! 

Share this post

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • 87 416-8 horse
      By 87 416-8 horse
      I’m looking for wheel horse tractors for sale or for parts in the Eastern Nebraska or western Iowa area. Preferably 8 speed manuals. Pm me or comment with what you have. The worst I could say is it’s out of my price or distance range. Edit: engine is not important, it’s going to get an engine swap.
    • BrianStasC-101
      By BrianStasC-101
      Hello all. I am looking for suggestions on adapting the pto from my C series tractor to a harbor freight predator 420 13hp engine. I know the predator motors are a controversial topic however it is the route I have chosen for this particular machine. The intent was to mostly use it for plowing so no PTO required but it would be handy to have. Looking to hear from someone that has successfully done the swap that may offer any advice before I attempt to transfer it over. Just looking for any general pointers that will help me along the way to make it go as smoothly as possible. 
    • HumbleHans
      By HumbleHans
      Operator manual 810343R1
      34 pages 17.5MB
      Wiring Colored 
      1 page 228KB
      1984 C-105 8-Speed model 11-10K802
      1984 C-125 8-Speed model 11-12K802
      1984 C-145 Automatic model 11-14KE01 - Some used alternate inner axle bearing See PSB #369
      1984 C-165 8-Speed model 11-16K801
      1984 C-175 Twin Automatic model 11-17KE01 - Some used alternate inner axle bearing See PSB #369
      1984 C-195 Twin Automatic model 01-19KE02
    • drewd
      By drewd
      Hi All,  I have a 71 or 72 Model # 101006, Serial # 790336.  Model number chart says 71 but the paper for the engine has a print code 72.  The closest I could find was for models 1-3745 & 1-3741.
      Two questions.  I finally need to replace the drive belt.  This manual list the belt as # 1576. 
      Two questions:
      1)  Does anyone know what size that translates to?  I do have the old belt but the inside edge is falling apart so it will measure a little longer than it should.
      2) This tractor has the electric clutch.  What is the best way to remove the belt?
      As always...Thanks!
    • t_furl43
      By t_furl43
      1979 c-101 nice project tractor just needs a few odds and ends, steering wheel, coil, carburetor bowl, the wiring was redone by previous owner....all 4 tires are good and hold air it goes into all gears no problem, transmission fluid has been changed, 10hp Kohler, message me or call or txt with any questions, it does run and runs well,  it’s been kept inside since I’ve had it, I would also trade for a mid mount grader blade thanks 

  • Create New...