'74 C160 Tecumseh engine tractor. Let's put it to use!

[ebinmaine 72,426]

@kpinnc

 

I had an order for McMaster Carr to place. 

Found them there.  

Thanks for the size reference.  

I also ordered a couple different thicknesses of washers.  

 

[ebinmaine 72,426]

Today I separated out all the new parts and continued clean up.  

 

 

 

Replaced all 3 axle grease fittings. 

Mounted the axle. Installed new nyloc nuts on the frame to attach-o-matic mount bolts 🔩.

 

 

 

 

[ebinmaine 72,426]

As explained in this video the hub was going to be out a hair to far. 

I needed to cut the spacer that the seal is going to ride on.

 

 

I used what I had to get the job done. 

Not exactly neat and clean...

but effective. 

 

 

 

After mounting the wheel on the hub on the axle I found I needed a wheel spacer.  

That's not at all surprising considering these wheels are universal camper or go-kart with a centered backspacing.

 

 

 

 

Here's a trial fit with the wheel on the spacer on the hub. 

 

 

That photo angle is a little misleading on the width. I can't get it too accurate yet but I think the front is going to be around 42", 43" across. The back is about 41".

 

 

[Handy Don 13,980]

19 hours ago, ebinmaine said:

I think the front is going to be around 42", 43" across

With the stock wheels/tires, the track for the swept axle is 42"

[ebinmaine 72,426]

8 minutes ago, Handy Don said:

With the stock wheels/tires, the track for the swept axle is 42"

 

I thought it was around that range somewhere. This definitely looks like it's going to be wider than that by a fair margin.

[Handy Don 13,980]

58 minutes ago, ebinmaine said:

 

I thought it was around that range somewhere. This definitely looks like it's going to be wider than that by a fair margin.

I just happen to have a swept axle with stock tires sitting in my storage area....

[ebinmaine 72,426]

7 minutes ago, Handy Don said:

I just happen to have a swept axle with stock tires sitting in my storage area....

 

Imagine that....

 

[ebinmaine 72,426]

I've had a hankerin'  to see the set of wiiide front tires on this beast but they just didn't quite do it for me.  

 

Well I have a set of 5  x 4.5 narrow wheels with tri ribs. 

Those look good! 

 

This evening I got the test fitted hubs and wheel spacers back off. 

Removed the dry fitted LH spindle. 

 

Got some grease in both spindles and installed them.  

 

I also used a tool I don't recall getting but it's super handy. A Bearing Packer.  

 

 

Also, I did some poking around here on the site because I should get new tie rods. 

I found an old post showing that I'll need to build some heim joint rods. 

The stock C160-8 steering plate won't clear the 520H tie rods. 

I'll check the threads another day and order from McMaster Carr.  

May have been @JAinVA that had that info years ago...

 

 

[ebinmaine 72,426]

Mission this morning is to get the adapter bushings held in place with a little J. B. Weld. 

 

 

 

 

Here's the 2,000 pound rated trailer hubs all set out and ready for installation. 

 

 

 

 

[ebinmaine 72,426]

Bushings are in place. 

 

Here's a wheel installed. 

 

 

 

 

Next project is to build tie rods. 

 

 

[ebinmaine 72,426]

Tie rods done. 

7/16 male/female brass colored from McMaster Carr. 

Center rod is threaded rod medium strength (much better than local hardware stores) 

 

 

Steering wheel held as close to center as my eyecrometer could get. 

 

 

Tie rod installation complete. Awaiting proper lineup.  

 

 

I used a piece of 6' long threaded rod for an "almost straight edge".

I then adjusted each side individually. 

 

I've come out about 3/4" total toe/tow in across the tires.  

 

 

 

 

 

 

Next is to get a @76c12091520h 2" receiver hitch installed.  

 

 

[AlexR 1,816]

That looks awesome good work!!!