Jump to content
RJ Hamner

Starter not able to turn rebuilt engine

Recommended Posts

RJ Hamner

Rebuilding a C160. everything worked prior to rebuild

Engine was fairly high time so machined .020 over and rebuilt

Finished rewiring and made sure all the circuits were in order

Starter would spin the engine. Made new coil wire and installed new spark plug

Starter won't turn the engine. Tried several times with and without spark plug Same results

Starter was what I took off the tractor prior to rebuild but can't say it is orininal

So.......Am I missing something or is a new starter going to be the answer?????

Thoughts?  Ideas?

All help/input appreciated

BTW:  Don't know if it means anything but the gear does not retract when key is moved back to ON

 

Bob

Share this post


Link to post
Share on other sites
 
ebinmaine

Have you bench tested that starter with battery cables while it is out of the tractor?

 

if it bench tests okay out of the tractor...

As to the Gear not retracting, you need to take the nut off the nose and take the spring out and whatever is in behind the gear and clean and dust it all off and put it back together with dry lube such as graphite powder.

Share this post


Link to post
Share on other sites
 
oldredrider

Is your battery hooked up correctly? Neg to ground, Pos to solenoid.

Share this post


Link to post
Share on other sites
 
RJ Hamner
46 minutes ago, ebinmaine said:

Have you bench tested that starter with battery cables while it is out of the tractor?

 

if it bench tests okay out of the tractor...

As to the Gear not retracting, you need to take the nut off the nose and take the spring out and whatever is in behind the gear and clean and dust it all off and put it back together with dry lube such as graphite powder.

 

My problem is it will turn over the engine without the spark plug but it doesn't have enough "oomph" to turn it over with the spark plug in

Share this post


Link to post
Share on other sites
 
R. L. Addison

Will the  engine turn over by hand? Was starter dropped during process of the work? Ceramic magnets break very easily in these starters. If engine turns over freely, bench test starter. If starter works as it should, then check battery & connections. 

 

My C141 started giving me starting problems last winter, & i found positive cable broke @ battery post. Whood a thunk? 

Share this post


Link to post
Share on other sites
 
The Tuul Crib

Could possibly be ignition switch?

Share this post


Link to post
Share on other sites
 
pfrederi

Load tested the battery???? 

 

After my Farmall M had its engine overhauled I had to get one of those optima batteries to get her to crank....

Edited by pfrederi

Share this post


Link to post
Share on other sites
 
Herder

Check your safety switches, pto, brake seat ect.

Share this post


Link to post
Share on other sites
 
bc.gold

Camshaft timing is off by one or more spurs, in this advanced valve  timing the intake valve is closing with an increased volume of gas and air mixture some of un-burnt fuel was intended to expel burnt exhaust gas when both the intake and exhaust valve overlap in the open position.

 

Competition pullers should have their camshaft dialed in as factory production cams may have the keyway cut a few degrees off from spec, this is part of blueprinting an engine.

 

Bendix gear is returned by spinning motion of flywheel, if the engine is a no start there's no energy to return the gear to a non engaged position.

 

camshafts-valve-overlap.jpg

 

 

Edited by bcgold

Share this post


Link to post
Share on other sites
 
JoeM

I would bypass the solenoid and touch the positive straight to the starter to and see if she will turn. I had those solenoids have high resistance not letting the starter build torque..

Share this post


Link to post
Share on other sites
 
squonk

Started could be worn enough internally to bind when loaded but soon with the plug out.

Share this post


Link to post
Share on other sites
 
RJ Hamner
24 minutes ago, OILUJ52 said:

I would bypass the solenoid and touch the positive straight to the starter to and see if she will turn. I had those solenoids have high resistance not letting the starter build torque..

 

17 minutes ago, squonk said:

Started could be worn enough internally to bind when loaded but soon with the plug out.

Both good inputs  I have ordered a new starter which should be here by next week.  Guess I had better order a new solenoid just to be on the safe side

 

Thanks guys!!!!!

 

Bob

Share this post


Link to post
Share on other sites
 
953 nut
5 hours ago, RJ Hamner said:

Don't know if it means anything but the gear does not retract when key is moved back to ON

 

5 hours ago, ebinmaine said:

As to the Gear not retracting, you need to take the nut off the nose and take the spring out and whatever is in behind the gear and clean and dust it all off and put it back together with dry lube such as graphite powder.

Eric has the answer. The Bendix is probably hung up due to dirt/grease build up on the shaft. 

When the engine was rebuilt I bet you painted everything real good. Paint is a very poor conductor of electricity, scrape the starter mounting, ground points and other electrical areas clean.

1483575903_1electrical.jpg.66a934f211a6755e2fa1ec2bdd6653de.jpg

Edited by 953 nut
  • Like 2

Share this post


Link to post
Share on other sites
 
bc.gold

http://www.badasscars.com/index.cfm/page/ptype=product/product_id=68/prd68.htm

How do cams affect compression?



How do cams affect compression?


This is a good one with no single answer. There are several types of compression such as "static" and "effective" (aka "dynamic") compression. It all has to do with cylinder pressure. Static compression is the actual mechanical compression ratio number that you get by combining a given piston size with a given combustion chamber size, with a given amount of stroke and displacement of the engine. So; bore, stroke, compression height, deck height, head gasket thickness and combustion chamber size, (among others), have to do with the "static compression", but they don't dictate the actual working or "effective" aka "dynamic" compression which directly affects "cylinder pressure". The cam dictates this for the engine.

 

Example: two identical engines both with 9:1 "static compression". The only difference is in the cam profiles. One has no overlap with a given intake valve timing to go along with the rest of the cam's profile, and the other has a lot of overlap with a completely different intake valve timing to go with that cam's overall profile. Overlap is the time in which both valves are open as the piston pushes exhaust out and starts to suck new fuel and air into the cylinder.

 

When the exhaust valve is closing and the intake valve begins to open, there is a time (on high performance and race cams) where both valves are actually open at the same time. As both valves are open, a little "reversion" gets pushed up the intake valve which slows the overall velocity down of the new fuel & air charge coming into the cylinder, and exhaust gas trying to still get out of the cylinder at low RPMs.

 

This overlap period in the valve timing is what causes that "rumpity rump" sound everyone likes so much. Overlap causes a "scavenging effect" as the engine RPM increases. This is why performance cams "come alive" at higher RPMs. It's not "just" the cam making the power, it's the cam's scavenging effect working as the RPM increases which increases cylinder pressure (dynamic or effective compression). Cylinder pressure makes the power. The downside to that rumpidy rump sound in most street engines is that the overlap also causes a decrease in manifold vacuum, making power brakes a nightmare and throttle response a bit sluggish.

 

When you have too much overlap, you end-up with a dog for an engine at low RPM's and the car will require things to make up for it such as low rear-end gears and high stall converters to help "spool the engine up" quicker to GET IT TO those higher RPMs where it can begin to do its scavenging thing and increase cylinder pressure. When you have too much overlap in an engine without enough static compression to support it, it is what's known as being over-cammed.

 

Lots of sound but not lots of GO, especially at low RPMs. Lots of engines out there are over cammed because guys like that rumpity rump sound, not knowing that although in many cases it may make more power at a higher RPM, it kills low-end power and torque which is what street performance engines should be concentrating on. TORQUE is what moves the vehicle below 4,000 RPM, not horsepower. Unfortunately, most guys only look at HP numbers, which is why there are a lot of turd cars out there.

 

Now, I get into arguments all of the time with guys who want to get technical with me, and they lose every time. They want to say that math and physics say horsepower and torque cross each other at 5,250 RPM, which is true, but that's where they CROSS, not where they are most effective! In other words, when it comes to torque, the closer your get to 5,250 RPM, the LESS EFFECTIVE torque becomes because horsepower is coming-up fast and takes over at 5,250. So the further you get below 5,250, the

 

MORE you rely on just torque for moving that vehicle. 95% o the time for most street cars, you are driving below 4,000 RPM, and usually under 3,000, so in those RPM ranges, you are almost solely relying on JUST torque to move that vehicle, therefore, in MOST situations, everything below about 4,000 or so you are pretty much relying on torque, NOT horsepower to move that vehicle. In the real world you aren't always relying on nerd math and literal physics. There is also a real world out there that has other variables working in it.

 

So back to those two identical engines with different cams; if you did a compression test on either of these two 9:1 static compression engines, the engine with no overlap (or even negative overlap) would probably have about 140 -150psi or so in the cylinders. The engine with more overlap may only have 110 - 120 psi or so, depending on how much overlap the cam has, how narrow the lobe separation angle is, and most importantly... what the intake valve timing is.

 

Some racing engines with 13:1 or so compression only have 125psi - 150 psi or so of cylinder pressure when a compression test is done. That's less than what most bone stock engines have. It just means that the cam has a ton of overlap and has intake valve timing designed to work with the rest of the cam's profile to create that scavenging effect, which in turn actually increases cylinder pressure at higher RPMs. Not to mention, if you do a compression test on a seriously high performance engine when it's cold, all of the components are at their loosest and don't provide much of a seal because they NEED the heat in the cylinders to expand the pistons and rings to make them seal better.

 

Static compression always stays the same. You can't change that unless you change the pistons or the heads, the head gasket thickness, etc. This is why race engines have "power bands" and come alive at higher RPM's. It's because the cylinder pressure increases as the engine RPM comes-up. It's from the scavenging effect from the valve timing and overlap in the cam, which raises the cylinder pressure and increases horsepower with RPM. 

 

This is what you are feeling when the cam comes alive or hits its power band. if it didn't have the scavenging effect, there wouldn't be much of a power band. It would just be smooth power all through the RPM range like any stock engine has.narrowing the lobe separation down also affects the power band. A wider lobe separation will smooth-out and "broader" the power band. On that very same cam, if you narrow the lobe separation, the power band will come-on a little higher in the RPM range, but when it comes-on, the power curve is steep and brutal. This is why hard core race cams have explosive power bands. The static compression never changed, but the effective compression surer did.

 

Many exotic modern cars these days have compression ratios MUCH higher than your average cars have. BMW M3's and M5's, Porsche 911's (non turbo), Ferrari's, Lamborghini's, etc., commonly have static compression ratios in the 11:1 - 12:1 area. In a regular car that is REALLY pushing it on 92 octane pump gas, but with EFI systems and knock sensors that adjust timing before detonation happens, they can get away with it. You ain't going to get away with that (reliably) with a carbureted engine, or an EFI engine without a knock sensor. As a rule of thumb (and this has a LOT of grey area), you can run upwards of 9.0 - 9.5:1 compression on pump gas with cast iron heads, and "about" one full point higher with aluminum heads because of how quick the combustion chambers cool.  Can you run 11:1 static on pump gas? Sure. There are still LOTS of older muscle cars running that have compression ratios that high that run on pump gas. You just have to back the timing off a little. Timing is VERY important when dealing with compression ratios, cams and fuel octanes.

 

Like I said in the beginning, there is no one answer to this whole ball of wax question. There are simply WAY too many variables involved. Let's just put it this way; we COMMONLY run compression up in the 10:1 area on our street engines (with aluminum heads) on 92 octane pump gas and they run BAD ASS, BUT we also commonly build them with between 9:1 - 9.5:1. It just depends on the circumstances and what our goal was with the engine.

 

  • Like 1

Share this post


Link to post
Share on other sites
 
WVHillbilly520H

@bcgold, I like that you took the time to write up the cam compression idiosyncrasies, but I'll will have to say with my current 406 SBC combo with a static CR of 10.3:1 and Dart Iron Eagle Platinum heads I get by quite well with 93 octane pump gas and 34° of timing, each engine build should be an individual blueprint to each intended use with stock, modified, or serious performance components, just my experiences and humble opinion. This screen shot is from a computer dyno simulator for my particular build.

Screenshot_20170518-195453.png

Screenshot_20170518-200410.png

  • Like 2
  • Excellent 1

Share this post


Link to post
Share on other sites
 
gwest_ca

Now that the engine has turned over a few times it might be worth rechecking the valve adjustment. The ACR (Automatic compression release) won't be effective if the gap is too wide.

 

Garry

  • Like 1

Share this post


Link to post
Share on other sites
 
RJ Hamner
On 1/1/2019 at 6:18 PM, OILUJ52 said:

I would bypass the solenoid and touch the positive straight to the starter to and see if she will turn. I had those solenoids have high resistance not letting the starter build torque..

 

On 1/1/2019 at 6:26 PM, squonk said:

Started could be worn enough internally to bind when loaded but soon with the plug out.

 

On 1/2/2019 at 8:37 AM, gwest_ca said:

Now that the engine has turned over a few times it might be worth rechecking the valve adjustment. The ACR (Automatic compression release) won't be effective if the gap is too wide.

 

Garry

Joe - replaced the solenoid

Squonk- Replaced the starter

With both of these items replaced it spins the engine at "warp six" but the final solution, thanks to gwest was an adjustment to the exhaust valve to allow the compression release to activate.

But the "Shame on Me Award" goes to ME.  With the exception of the compression release all this could have been avoided if I had NOT reused the old starter and solenoid.  This was the first time I have ever done this on a "ground up" restore.  That's what I get for trying to save a buck.

BTW:  Now that I think I've learned my lesson there may be one or two items that will get replaced

 

Thanks guys for all the input

 

Bob

  • Like 1

Share this post


Link to post
Share on other sites
 
JoeM

Nice, post a video if you can, I bet that thing sounds sweet!

 

Share this post


Link to post
Share on other sites
 
RJ Hamner

Will try to get a video. Waiting on a couple more parts. BTW. How's the leg doin'??

Share this post


Link to post
Share on other sites
 
LengerichKA88

Nevermind

Edited by KyleLengerich
  • Like 1

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • Brad Schroder
      By Brad Schroder
      Looking for 701 (k161) parts. Starter/generator, right side belt cover, left side belt cover, air cleaner housing. Thanks
    • Maxwell-8
      By Maxwell-8
      So yesterday I picked-up a C175. She was rusting away as she was stored outside. She had a new to her Kohler K341. @squonk The previous owner indeed better had"LET AN ELECTRICIAN      CHECK his  SHORTS!"  as bad wiring shorted the battery out, and exploded/melted. She has a Sundstrand hydro pump with a Filter, is that normal? By the pump I believe it's a 1980. But you never now for sure as it's made in Oevel. Due to the bad wiring, the engine was in no running condition. But don't think the K341 has many hours on it. The hydro I don't know if it works. She was hard to push. So i lift up one wheel, so we could roll here one one wheel and the diff prevented the trans from locking up.
      So first things to do:
      1) get the engine running
      2) replace the steering wheel, but don't think removing it will be very hard as it's already split in two.
      3) replace the axleseals, the oil leak caused a lot of sandbuild up as she was mainly used on for leveling out a horse track.
      4) clean all the acid and remove all the old wiring to do a full rewiring
      5) replace the plastic seat pan with a metal.
      6)...
       
      I'm looking forward on my first C. 
      It's also my first hydro, I don't know a lot about them and prefer actual gears. Simpler and need less maintenance (parts-shortage). 
      But since I couldn't find another project WH and me hearing a lot of good things about hydro's  on the forum..  I finally took the shot.  








    • Bill D
      By Bill D
      I bought this K341 and was wondering what it came on originally.  It's a 13 fin block and has been bored .020 over already.  It has a Kohler carb which may not be original.  Bill

    • Chuck14025
      By Chuck14025
      1994 520 H.   Starter just clicks.
      1. Battery 12.6V, load test OK.,    New solenoid. Ground good. Key switch tested ok. Wiring diagram shows a 'kill' relay - I can't find it on the tractor. Checked the 3 relays under the battery box - they work. Neutral switch, PTP and seat switch work mechanically. 
      2. Not able to find article on this problem when searching. There must be dozens. How do I find them?
      3. Can I test the starter without taking it out?
      4. Is there a 'kill' relay? 
       
      thank you...
       
    • ToroWheelHorseRookie
      By ToroWheelHorseRookie
      Please Help-- I inherited this work horse from my father in-law after being passed down from his father.  I recently brought my wheel horse in for repairs and the service shop said they were unable to find the part; starter/solenoid.  I did not want to give up on this beast as even the repair shop said this is a well made machine and is better than anything built today. I eventually found the part but because the shop left the part uninstalled I was unable to see how the starter was wired.  Yesterday,  I installed the new starter/solenoid but when I connected the battery terminals the tractor wanted to start on its own.  I quickly disconnected the terminals and analyzed the electrical schematic map but I am baffled on the proper wiring.  I only have a positive (red) battery terminal wire, another red wire, black (ground) wire, and a blue wire with a slot connection.  I included pictures of the starter and the electrical schematic map.  Any help would be much appreciated!! I l would like to fix this on my own as this seems to be a simple wiring issue.  I can add pictures of the tractor itself, but at the moment its under a tarp in a shed at night. Thank you in advance, Matt     


      Electrical Guide.pdf
×
×
  • Create New...