Jump to content

Search the Community

Showing results for tags 'fingers'.

More search options

  • Search By Tags

    Type tags separated by commas.
  • Search By Author

Content Type


  • Wheel Horse
    • Wheel Horse Tractors
    • Wheel Horse Electric / Battery Powered Tractors
    • Engines
    • Transmissions and transaxles
    • Wheel Horse Electrical
    • Implements and Attachments
    • Restorations, Modifications, & Customizations
    • Pullers
    • WIKI Discussion
  • Wheel Horse Reference
    • Wheel Horse Manuals
    • RedSquare Links
    • Instructional threads and video's
    • Tools and Equipment
  • Europe
    • Euro Introductions
    • Show Pictures
    • Euro Classifieds
  • Picture Gallery
    • Wheel Horse Picture Gallery
    • Implements Picture Gallery
    • Show Pictures
    • LIVE Broadcasts
  • Classifieds
    • Classifieds
    • Haulin Help
    • Vendors
  • General Talk
    • non tractor related discussion
    • Introductions
    • Bumps and Bruises
    • site suggestions, updates, issues
    • Just for Fun
    • other brands
    • Gardening
  • Shows and Events
  • 520 Club's 520 Specific


  • Wheel Horse Manuals
    • 1955-1964
    • 1965-1972
    • 1973-1977
    • 1978-1984
    • 1985-1990
    • 1991-1997
    • 1998-2012
    • All years
    • Service Bulletins
  • Implement Manuals
    • Mower decks & reel
    • Blades Dozer Grader Snow
    • Snow Blowers
    • Ground engaging
    • Other
  • Engine Manuals
    • Kohler
    • Onan Service Manuals
    • Other
  • Transmission
    • Manual
    • Automatic / Hydro
  • Electrical
  • Brochures
  • RedSquare Calendars
  • Wheel Horse 3D
  • Misc. Items


There are no results to display.

There are no results to display.


  • Wheel Horse for Sale
  • Euro Wheel Horse For Sale
  • Wanted
  • Euro Wanted
  • Vendors
    • K&B Wheelhorse Parts
  • Trade
  • Euro Trade
  • Non-Wheel Horse
  • Euro non-Wheel Horse
  • Wheel Horse Sold Archive

Find results in...

Find results that contain...

Date Created

  • Start


Last Updated

  • Start


Filter by number of...

Found 1 result

  1. Finally finished the chicken plucker implement. Okay, it ain't purdy, but it's going to be put to use tomorrow. Will take video of it in action. It's a bit on the heavy side, but it attaches in two parts. The primary frame attaches to the tach-a-matic. The secondary frame slides from left to right into a receiver on the primary frame. The secondary belt is installed at this point, the secondary frame is then slid left to take up the slack in the belt. A hand knob on the bottom is tightened to secure the secondary frame and secondary belt. The primary belt is the tiller belt, repurposed, threaded from pto to the mule drive to the 10" pulley on the primary frame. The secondary belt further reduces the rpm 5:1. I designed the gear reduction to be approximately 12:1. For the C-125, that should result in variable speed of the feather plate between about 175 to 280 rpm. I put a photo tach to it and got a reading of about 100 rpm at idle. At WOT it was about 275 rpm. Low end was out of line. Either the engine is idling too slow or I've got some slippage. I'll have to check it more thoroughly as the numbers were jumping around quite a bit. I may not have had the best conditions for accurate measurement. Anyway... here it is! After I use it tomorrow, maybe I'll knock off some of that rust and give it a paint job. Or, maybe I'll just start the next project!
  • Create New...