What have you done to your Wheel Horse today?

[squonk 47,117]

23 minutes ago, Sparky said:

Old gear oil out, then a kerosene flush and drain…now the fresh stuff goes in.

1978  C-81 

 

Something tells me you didn't spend the afternoon on a black roof in this heat! 

[ebinmaine 79,346]

Page number.      1054 !!

 

[Sparky-(Admin) 25,745]

 Was not a fan of these big goofy headlights on my 857, after two years of owning it I finally removed them. 
  Much better looking! Too bad there’s a big ‘ol hole on both sides of the hood 

 

 

 

[EthanL 16]

6 minutes ago, Sparky said:

 Was not a fan of these big goofy headlights on my 857,

 

 

 

My tractor had the same round lights, they got old and burned out. Rather than replacing them I found new LEDs that looked very similar. Since this tractor is my work horse, the LEDs were a very functional upgrade. 

[ebinmaine 79,346]

13 minutes ago, Sparky said:

big goofy headlights

 

If ya need a home for those.. I'd be interested. 

[Sparky-(Admin) 25,745]

9 minutes ago, EthanL said:

My tractor had the same round lights, they got old and burned out. Rather than replacing them I found new LEDs that looked very similar. Since this tractor is my work horse, the LEDs were a very functional upgrade. 

 And yes, if this was a worker I would have kept the headlights. But it’s pretty much just a show cruiser. Occasionally I’ll hook up a trailer and move firewood but never at night. 

[Handy Don 16,815]

18 minutes ago, Sparky said:

I'm sure you can find something to attach there that is more pleasing to look at, for example a side marker light or a simple reflector.

You might consider, too, a reinforced filler covered by a decal from redoyourhorse--something custom, even, like your horse’s name. 

I do agree those lights look better in the parts bin than on the tractor! 

 

[Handy Don 16,815]

On 6/29/2026 at 6:05 AM, adsm08 said:

In fact I may grab those ones and use them since that deck now has a broken cross shaft.

I have found two potential “gotchas” on these decks when mixin’ & matchin’ apart from those driven by the 32 vs 36” sizes. 

In ’68, WH added shoulders on the bottoms of the cross-shaft bearing holders around the mounting bolt holes. I believe it was better for locking in cross shaft alignment. These then needed enlarged holes through the shell and into mating sockets in the cast iron bearing holder.

In, I think, ’66 or ’68, the spindles were lengthened by ⅛” to accommodate a thrust bearing below the spindle gear--previously there was a simple thin thrust washer. 

[squonk 47,117]

48 minutes ago, Sparky said:

 Was not a fan of these big goofy headlights on my 857, after two years of owning it I finally removed them. 
  Much better looking! Too bad there’s a big ‘ol hole on both sides of the hood 

 

 

 

Red Square stickers would cover them up!

[adsm08 4,710]

32 minutes ago, Handy Don said:

WH added shoulders on the bottoms of the cross-shaft bearing holders

 

I believe the ones on the 32 inch deck had them. I have not inspected the ones from the 36 we just took apart yet.

[sqrlgtr 3,078]

1 hour ago, Sparky said:

Too bad there’s a big ‘ol hole on both sides of the hood 

had a set of extra holes in my 1257 hood but added lights instead of removing 

[ML3 2,353]

10 minutes ago, sqrlgtr said:

had a set of extra holes in my 1257 hood but added lights instead of removing 

My free 702 already had holes w/no lights installed.  Since its a functional tractor I installed led lamps. They definitely work great & at least I dont think they look too bad......It kinda ugly old tractor anyways! 🤣

[wfopete 38]

My "New to Me" D160 Kept pushing the dip stick out of the tube.  I knew that wasn't right and did some digging about the Onan B43 in it.  Took apart the breather reed valve assembly and was surprised that Lufkin made the reed; boy that reed was stiff too!  You know what? Lufkin also made feeler gauges and this reed measured in at .0275".  Me thinks bubba was at work here. 

 

My OEM replacement reed was a little more flexible at .0060".  I think the reed problem is solved. 

 

 

               

Edited 16 hours ago by wfopete

[CasaytheMann 168]

Pulled both mower blades and sharpened them.

[Lee1977 7,657]

16 hours ago, Sparky said:

 Was not a fan of these big goofy headlights on my 857, after two years of owning it I finally removed them. 
  Much better looking! Too bad there’s a big ‘ol hole on both sides of the hood 

 

 

 

 

 

 

I had a couple hole drilled in my 312-8 when I got it. I pushed in a couple body panel plugs, mine were in the black so I didn't have to paint them.

[peter lena 9,920]

@Lee1977 those body panel plugs make it easy , pete

[RJR49 164]

Installed a "go" pedal on my C-160 Auto. This is the 3rd, and I believe, the simplest, and most elegant of the three versions. Very easy to do. I'll create some drawings if anyone is interested.

[kdeatrick 153]

Saturday after leaving the show, I pulled all the Work Horses out of the Horse Garage and clean the garage and them. I rebuilt the garage last fall 1 board at a time, only thing left original is the roof.

I have another restored 1848 to bring over that will live here now also. Still 1 more GT1100 at home and 1 at the cabin. Plus a C175 disassembled and on pause of restoration. a bunch of decks for spares. I think the GT1600 shown here maybe next, I have the engine ready to reassemble after being bored.