Jump to content
KC9KAS

Lawn & Garden Tractor Magazine article

By KC9KAS, in Wheel Horse Tractors

Recommended Posts

KC9KAS    4,746

KC9KAS
Posted (edited)

Just read my L&GT magazine and found a very nice article about Gary Cribbs and his Wheel Horse tractors.

He gives a very nice "plug" for Red Square!

 

Also in the magazine is a very good article by Norman Ng on the use of a multimeter.

Edited by KC9KAS
  • Like 4
  • Excellent 2

Share this post

Link to post
Share on other sites
 

tunahead72    2,627

tunahead72
Posted
14 hours ago, KC9KAS said:

... Also in the magazine is a very good article by Norman Ng on the use of a millimeter.

 

Uh, would that be multimeter?

 

And is that Norman from isavetractors?

 

  • Like 1
  • Haha 1

Share this post

Link to post
Share on other sites
 

KC9KAS    4,746

KC9KAS
Posted
9 hours ago, tunahead72 said:

 

Uh, would that be multimeter?

 

And is that Norman from isavetractors?

 

Yes on both accounts....Damn spellcheck!

  • Haha 1

Share this post

Link to post
Share on other sites
 

WHX??    56,059

WHX??
Posted (edited)

Yes he did have a nice plug for RS. What is his handle here? Being featured  collector is quite an honor and any machinist by trade is a friend of ours! Our very own @chris sutton got a mention from a reader write in about his UK Wheel Horse Round Up and a nice article about Pond walk b-hinds in this issue too! :greetings-clappingyellow:.

Edited by WHX12
speeling
  • Like 1
  • Excellent 2

Share this post

Link to post
Share on other sites
 

wallfish    19,733

wallfish
Posted
28 minutes ago, WHX12 said:

and a nice article about Pond walk b-hinds in this isue too

Our own RS member @grnlark ( AKA Matt ) is writing a Wheel Horse article for every issue now. We were talking about it at Zagray's and Stevebo's M&G and he has some pretty good ideas and a plan so keep an eye out for some more good WH stuff from him.

 

  • Like 3
  • Excellent 1

Share this post

Link to post
Share on other sites
 

WHX??    56,059

WHX??
Posted

Ooooh  I like that news John .... can't wait! :handgestures-thumbupright:

Share this post

Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Go To Topic Listing

  • Similar Content

    • rustyedge1
      OME 417-8 drive belt needed
      By rustyedge1
      The local place I’ve bought parts from for years has changed owners, now they can’t even spell Wheel Horse let alone be if any help.
      Doing my spring tune up I noticed my drive belt is getting pretty ratty. Due to all I’ve read thought I’d ask for some advise on getting it right the first time on a new belt.
      Is there still dealers on this site selling OME stuff ? I know there are tons of aftermarket crap but not looking for that.
      Thank in advance.
       
       

    • rustyedge1
      NEED Condenser for 8 HP Kohler
      By rustyedge1
      Need a condenser for engine shown in photos 8 hp Kohler. Any venders carry them on this site ?
      All help appreciated..Have PayPal or can send check..


    • WheelPuke
      89 400 series 25A fuse blowing
      By WheelPuke
      I have my 25A fuse blowing every time I put a new one in the slot. The old one was burnt up when I got the tractor put this year. It sat for a year with a dead battery. I stopped using it as much because the transmission is clattering pretty bad when taking off on second or higher. I had to replace the clutch belt a few years ago and couldn't get an OEM. Not sure what is the problem there that's another issue though.
       
      I have checked the wiring and patched the worn spots where it could be grounding out. The fuse blows as soon as there is power to the system with the ignition off. I'm at a loss of what to check for at this point. Any input from someone who has had this issue would be appreciated. I'm not sure what these units are in the photos but do not know how to test them for a failure. They are directly in loop with the battery and the ignition loom looks to run into that 25A fuse.

    • Redtickuleez
      My New d180/wife upsetter
      By Redtickuleez
      Hello gentlemen!!! I recently bought a d180 with loader and backhoe. Im looking for serial number.. there is a plate under the steering wheel but its been pajnted over and i can make it out. Can y'all tell me another location and was this tractor pruchased originally with these attachments and any info would be greatly appreciated... Thanks fellow Wheel Horse enthusiasts !!! !! !!!
    • Aaron Coffman
      "Pond" Wheel Horse Walk Behind
      By Aaron Coffman
      Hi Red Square Community,
       
      I am looking into purchasing the below pictured "POND" Walk Away. The unit itself has the cast in “POND” on the chain reduction housing. The two main things I am looking to learn are what value is typical for these to sell for. This one has a Briggs & Stratton model “N” engine. It runs and drives, but the throttle linkage needs some adjusting. It comes with a cultivator and plow implement. 
       
      Secondly, I was wondering if there is any way to determine what year specifically this Pond is from. The seller believes late 1940s and not 1950s. I am new to these machines, so I am looking for some guidance. Thank you in advance! 
       

×
×
  • Create New...