Jump to content
D250power

D250

Recommended Posts

D250power

Hi I am looking for a distributor drive gear for the Renault 800  on the d250.  Also a cylinder head. I lost the gear.

Share this post


Link to post
Share on other sites
 
benji756

There is a new posting from a member who just acquired what appears to be a d-250 he may be interested in selling you what you need.

The posting is mystery horse please help

  • Like 1

Share this post


Link to post
Share on other sites
 
953 nut

:WRS:              Here is the post, perhaps the two of you can work a deal.

 

Share this post


Link to post
Share on other sites
 
D250power
18 hours ago, benji756 said:

There is a new posting from a member who just acquired what appears to be a d-250 he may be interested in selling you what you need.

The posting is mystery horse please help

 

Hi  sounds good what would you want for the parts. 

Share this post


Link to post
Share on other sites
 
953 nut
4 minutes ago, D250power said:

 

Hi  sounds good what would you want for the parts. 

Send a PM (personal message to member @Levi, he is the one who has the other "D".

Share this post


Link to post
Share on other sites
 
D250power

I am not sure how to maneuver around red square an contact members 

Share this post


Link to post
Share on other sites
 
953 nut
26 minutes ago, D250power said:

I am not sure how to maneuver around red square an contact members 

On the home page at the upper right side you will see an little envelope. Click on it and then click on compose new message, a PM form will come up;  in the "TO" line put in the person you want it to go to, in this case Levi. then fill out the form and send it.

Take a look at this.

http://www.wheelhorseforum.com/forum/56-finding-your-way-around-in-redsquare/

  • Like 1

Share this post


Link to post
Share on other sites
 
Ed Kennell
33 minutes ago, D250power said:

I am not sure how to maneuver around red square an contact members 

Click on the en.....  Dick types faster than me.:)

  • Haha 1

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • 850ford
      By 850ford
      I am looking for a replacement Kohler for a 1980 c165,it is cradle mounted.
      Will a standard mount Kohler work, if I remove the cradle?
       I am located in Massachusetts 
        Thanks
    • BrianStasC-101
      By BrianStasC-101
      Hello all. I am looking for suggestions on adapting the pto from my C series tractor to a harbor freight predator 420 13hp engine. I know the predator motors are a controversial topic however it is the route I have chosen for this particular machine. The intent was to mostly use it for plowing so no PTO required but it would be handy to have. Looking to hear from someone that has successfully done the swap that may offer any advice before I attempt to transfer it over. Just looking for any general pointers that will help me along the way to make it go as smoothly as possible. 
    • Tenday
      By Tenday
      Experts - help please. I’m new to Wheel Horse Tractor life! 
       
      So - I’ve pulled out an inherited tractor and have decided to resurrect her. Unfortunately, no spark :/ 
       
      I’m looking for help on diagnosing no spark. 
       
      model - 417-8 
      engine - Kohler KT17
       
      Done thus far:  (aware that some have no implication on spark.) 
       
      - new ignition switch 
      - new battery 
      - new starter
      - new ignition coil and wires w/ plugs 
      - new condenser 
      - new points 
      - new starter solenoid 
      - bypassed all switches except oil and seat. 

      notes:

      idiot lights removed. 
       
      All fuses tested with Ohms as well as visual inspection  .. 
       
      coil tested w/ ohms as well
       
      all switches bypassed except: 
      -oil switch  ( don’t think it has any implications other than a visual indication for idiot lights. ) 
      -seat switch 
       
      ran a pos from batt direct to pos of coil - nothing; no spark. 
       
       
      Electric is as follows:  
       
      - Starter switch wired to solenoid
      - - solenoid to starter 
      - - solenoid to batt
       
      - one wire from starter switch goes to engine ( I think this is for batt charge / flywheel) 
       
      - I have two yellow wires, which are married up, that go to engine which have constant power; They power coil.  Comes from switch and seat. 

       
       
       
      Help - what the heck am I missing ? 
       
       
       
       
       
       
       
    • DVail2000
      By DVail2000
      Ok, So I am seeing that most of you are leaning towards the ONAN engines being crap.  That said, I have 2 416's  # 1 is a -8 and # 2 is a -H.  Both have the -216 in them.  i was thinking of rebuilding the engine from the 416-H, but I am also considering changing the engine out with a different type.  What are the recomendations? I am seeing Koler, what else will fit?
       
       
      Thanks
       
      Dave.
×
×
  • Create New...