Jump to content
Sign in to follow this  
coldone

D200 Pressure test vid.

Recommended Posts

coldone

Here is the vid of me performing a preesure test on the D200. I had mowed the entire yard with it earlier today then parked it for a few hours. The engine was still warm to the touch but the hard lines were ambient temp.

[media=]

  • Like 2

Share this post


Link to post
Share on other sites
 
pfrederi

Nice Video. You did a great job!

The alternative pressure hook up is an #6 ORB (O ring boss). It is on the top of the pump. I would like to permanently mount a pressure gauge but i haven't figured out how to plumb it and have room for the battery.

Share this post


Link to post
Share on other sites
 
Trouty56

Good video....just one thing though.....did you say "back to the steaks"...?? Those steaks would have been too well done for me already...lol... All jokes aside...great job all round. By the way...I'm a big fan of surplus center.

Share this post


Link to post
Share on other sites
 
JamesBe1

Excellent vid. Thanx for posting that.

You might not want to trust the accuracy of the mechanical pressure gage below 10% of range. It's more for qualitative purposes than quantitative. But at least it's showing that you have pressure when you should have pressure. Also, one heck of a great job on the motor rebuild. I enjoyed the pics. I might not be so squeamish about opening one up next time.

I have been pondering adding a hydro pressure gage in the dash where the hours meters goes. Not sure if I can even find a 2' recessed pressure gage though. Still, I don't think I would want to run a 1k PSI pressure line up there if I don't have to. I would want to find a way to use an electrical sensor and gage instead.

But the most important thing was the steaks! I hope you enjoyed!

Share this post


Link to post
Share on other sites
 
coldone

Good video....just one thing though.....did you say "back to the steaks"...?? Those steaks would have been too well done for me already...lol...

Yes I said steaks and yes they were too done but I promised yall a video. They were still juicy just a little too well done no pink in the middle. :D

  • Like 1

Share this post


Link to post
Share on other sites
 
JackC

Thanks for the video.

Share this post


Link to post
Share on other sites
 
1maidenfan

Good video....just one thing though.....did you say "back to the steaks"...?? Those steaks would have been too well done for me already...lol...

Yes I said steaks and yes they were too done but I promised yall a video. They were still juicy just a little too well done no pink in the middle. :D

Gotta like the "pink in the middle" :ychain:

Excellent video. :bow-blue:

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Similar Content

    • BuffaloD200
      By BuffaloD200
      Finally getting around to working on my ark loader.  The previous owner said he thinks the problem is with the spool valve.  
      As I've learned a bit more about hydraulics now, I'd like to get this all sorted out.  
      I noticed the power beyond port is connected to the reservoir return.  Is that right?  
      Anyone see anything blatantly incorrect?



    • ccs002
      By ccs002
      Looking for a complete hydro pump for a D-160. Tractor is missing everything from the rubber coupler disc back. Also willing to buy a complete tractor for parts, the closer to Harrisonburg VA the better. Thank you. 
    • eo1bart
      By eo1bart
      Looking for a gearbox with 1 1/8" axles for my 312. Ok if it needs rebuilding.
      Located in the New England area
    • cheesegrader
      By cheesegrader
      About a decade ago, I bought a conversion kit here to remove the column drive lever and convert to a foot pedal for a 520h.
      I would like to convert a second tractor, and I need to replace one of the linkage bars on the first one that has cracked, but I can't find the vendor any more.
      Does anyone remember who made this awesome mod, and where I can find them?
    • giant_g2
      By giant_g2
      Not sure on specific model. This 8 spd came attached to a plow I bought. It had some water in it for a couple weeks according to the prior owner. I drained it, sloshed some diesel in it, drained that, then filled with fresh oil. Spinning the input shaft by hand, I can see the axels turn. Hasn't leaked any oil. I'm not really interested in shipping, so I'd prefer local sales.

×
×
  • Create New...