8ntruck 9,405 #1 Posted 18 hours ago I've been towing with a 2015 Ram 1500, using a hitch with a 2" drop. This made the trailers I tow run with ith the toung running slightly down hill. On the last trip we took with the ALiner, I switched to a zero drop hitch. This has the toung of the ALiner real close to level. This change made the ALiner 'feel' better to tow over the 2" drop hitch. I'm wondering why this is. Part of me thinks it feels better, just because I think it should help. Other parts of me wonder if the toung angle turns any camber in the trailer wheels into tow in or tow out, or maybe the small shifts in the trailer's center of gravity in relation to the wheel hubs changes the towing dynamics of the trailer. Thoughts? Comments? 2 Share this post Link to post Share on other sites
Bar Nuthin 3,539 #2 Posted 18 hours ago (edited) Close to level is usually best. Too high shifts the load backwards and can make a trailer prone to swaying. To low shifts the weight forward and can lighten the front wheels of the truck and make them feel less in touch with the road. Edited 18 hours ago by Bar Nuthin typo 4 Share this post Link to post Share on other sites
SylvanLakeWH 32,832 #3 Posted 17 hours ago I try to run them roughly level. However, load distribution and tongue weight are factors for empty vs. full load... I always load my utility trailer so there is adequate tongue weight to keep the trailer firmly on the hitch. 3 Share this post Link to post Share on other sites
Tonytoro416 1,396 #4 Posted 17 hours ago Overall trailer length with also effect how this feels ( better or worse) my little 12 ft utility trailer has to be pretty level when loaded on my truck. Tongue angled forward or down makes the trailer almost constantly wagging slightly when empty. My longer trailer doesn’t get the sway like the shorter utility does 2 Share this post Link to post Share on other sites
Ed Kennell 47,833 #5 Posted 7 hours ago If you have proper tongue weight on the ball ( 10 to 15% of the trailer weight ) I doubt if a 2" change in ball height will make any significant change in tongue weight. My guess is the cantilevered geometry of a dropped or raised hitch would magnify the forces from the trailer. A straight hitch would minimize these forces giving a smoother ride in the towing vehicle. 2 Share this post Link to post Share on other sites
ranger 1,863 #6 Posted 7 hours ago I would imagine that the height of the towing coupling would have the greatest effect on towing if the trailer has more than one axle, and the axles were independent of each other? I’ve seen many twin axle trailers being towed with either the front wheels or the rears hardly touching the ground! Usually behind trucks with heavy duty suspension that doesn’t give way enough to allow the trailer to level itself out. If the hitch is too high, the trailer structure can fail, (rear axle carrying all the load). If too low, it’s like towing a trailer with all the load at the rear, (front axle carrying all the load) = swaying. 1 Share this post Link to post Share on other sites
peter lena 10,114 #7 Posted 6 hours ago @8ntruck dare to ask this ? have any related lubrication . on that ball / swivel , lever set up ? most of the stuff I see is solid rust , pete Share this post Link to post Share on other sites
Handy Don 17,684 #8 Posted 6 hours ago 12 hours ago, 8ntruck said: Other parts of me wonder if the toung angle turns any camber in the trailer wheels into tow in or tow out, Unless load distribution or some other factor changed, I think you have hit the nail on the head here. The trailer suspension is likely tuned for level towing. Share this post Link to post Share on other sites
8ntruck 9,405 #9 Posted 6 hours ago 10 minutes ago, peter lena said: @8ntruck dare to ask this ? have any related lubrication . on that ball / swivel , lever set up ? most of the stuff I see is solid rust , pete I put a dolip of general purpose chassis grease on the hitch ball before a long trip - no need for high drop point grease in this application. 1 Share this post Link to post Share on other sites
Ed Kennell 47,833 #10 Posted 3 hours ago These towing posts always remind me of my near disaster. One of my earlier camping rigs was a 1980 Ford Bronco and a 27' dual axle Mobile Traveler trailer that weighed nearly 7K lbs. The trailer had electric brakes on all four wheels and the Bronco had a variable brake controller with the emergency lock up switch. They were connected with a good weight equalizer hitch and an anti sway link. I had towed this rig over the Appalachians and Rocky mountains and at 65 MPH on trips to Florida. It drove and handled like a long wheel base Greyhound coach bus. Then one day i didn't bother to connect the equalizer, anti sway or brakes for the 3 mile trip to the inspection station. At about 45MPH going down a slight hill the trailer went into a violent oscillating .sway that nearly turned the entire rig over. Braking with the Bronco only increased the sway and I eventually coasted to a stop. This camper had a long fresh water tank located in the rear of the trailer. The tank was as wide as the trailer. I assume the side to side shifting of the water is what caused the problem. Just something to remember when hauling liquid. 2 Share this post Link to post Share on other sites