Jump to content
8ntruck

Hitch Height

Recommended Posts

8ntruck

I've been towing with a 2015 Ram 1500, using a hitch with a 2" drop.  This made the trailers I tow run with ith the toung running slightly down hill. 

 

On the last trip we took with the ALiner, I switched to a zero drop hitch.  This has the toung of the ALiner real close to level.  This change made the ALiner 'feel' better to tow over the 2" drop hitch.

 

I'm  wondering why this is.  Part of me thinks it feels better, just because I think it should help.  Other parts of me wonder if the toung angle turns any camber in the trailer wheels into tow in or tow out, or maybe the small shifts in the trailer's center of gravity in relation to the wheel hubs changes the towing dynamics of the trailer.

 

Thoughts?  Comments?

  • Like 2

Share this post


Link to post
Share on other sites
 
Bar Nuthin

Close to level is usually best. Too high shifts the load backwards and can make a trailer prone to swaying. To low shifts the weight forward and can lighten the front wheels of the truck and make them feel less in touch with the road.

Edited by Bar Nuthin
typo
  • Like 4

Share this post


Link to post
Share on other sites
 
SylvanLakeWH

:text-yeahthat:

 

I try to run them roughly level. However, load distribution and tongue weight are factors for empty vs. full load... I always load my utility trailer so there is adequate tongue weight to keep the trailer firmly on the hitch.

  • Like 3

Share this post


Link to post
Share on other sites
 
Tonytoro416

Overall trailer length with also effect how this feels ( better or worse) 

my little 12 ft utility trailer has to be pretty level when loaded on my truck. Tongue angled forward or down makes the trailer almost constantly wagging slightly when empty.  My longer trailer doesn’t get the sway like the shorter utility does 

  • Like 2

Share this post


Link to post
Share on other sites
 
Ed Kennell

If you have proper tongue weight on the ball ( 10 to 15% of the trailer weight )  I doubt if a 2" change in ball height will make any significant change in tongue weight.

My guess is  the cantilevered geometry of a dropped or raised hitch would magnify the forces from the trailer. 

A straight hitch would minimize these forces giving a smoother ride in the towing vehicle.

  • Like 2

Share this post


Link to post
Share on other sites
 
ranger

I would imagine that the height of the towing coupling would have the greatest effect on towing if the trailer has more than one axle, and the axles were independent of each other? I’ve seen many twin axle trailers being towed with either the front wheels or the rears hardly touching the ground! Usually behind trucks with heavy duty suspension that doesn’t give way enough to allow the trailer to level itself out. If the hitch is too high, the trailer structure can fail, (rear axle carrying all the load). If too low, it’s like towing a trailer with all the load at the rear, (front axle carrying all the load) = swaying.

  • Like 1

Share this post


Link to post
Share on other sites
 
peter lena

@8ntruck  dare to ask this  ? have any related lubrication . on that  ball / swivel , lever set up ?  most of the stuff I see is solid rust , pete

Share this post


Link to post
Share on other sites
 
Handy Don
12 hours ago, 8ntruck said:

Other parts of me wonder if the toung angle turns any camber in the trailer wheels into tow in or tow out,

Unless load distribution or some other factor changed, I think you have hit the nail on the head here. The trailer suspension is likely tuned for level towing. 

Share this post


Link to post
Share on other sites
 
8ntruck
10 minutes ago, peter lena said:

@8ntruck  dare to ask this  ? have any related lubrication . on that  ball / swivel , lever set up ?  most of the stuff I see is solid rust , pete

I put a dolip of general purpose chassis grease on the  hitch ball before a long trip - no need for high drop point grease in this application.

  • Like 1

Share this post


Link to post
Share on other sites
 
Ed Kennell

These towing posts always remind me of my near disaster.     

One of my earlier camping rigs was a 1980 Ford Bronco and a 27' dual axle Mobile Traveler trailer that weighed nearly 7K lbs.   The trailer had electric brakes on all four wheels and the Bronco had a variable brake controller with the emergency lock up switch.   They were connected with a good weight equalizer hitch and an anti sway link.  I had towed this rig over the Appalachians and Rocky mountains and at 65 MPH on trips to Florida.     It drove and handled like a long wheel base  Greyhound coach bus.

 

Then one day i didn't bother to connect the equalizer, anti sway or brakes for the 3 mile trip to the inspection station.

At about 45MPH going down a slight hill the trailer went into a violent oscillating .sway that nearly turned the entire rig over.

Braking with the Bronco only increased the sway and I eventually coasted to a stop.  This camper had a long fresh water tank located in the rear of the trailer.  The tank was as wide as the trailer.  I assume the side to side shifting of the water is what caused the problem.  Just something to remember when hauling liquid.

 

  • Like 2

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...