Dimensions needed for Mid Mount Grader Blade Bracket

[BradKahler 266]

I'm building a mid mount grader blade for my B80 and I've found a lot of information but I'm lacking a couple of dimensions and an angle.  Any chance one of you might have access to one of these and be willing to provide the needed information?

 

Thanks!  

 

Brad

 

 

[ebinmaine 78,085]

45 minutes ago, BradKahler said:

Any chance one of you might have access to one of these and be willing to provide the needed information?

 

 

 

 

 

 

We have a couple Mid Mount Grader Blades here. I can get you those measurements tomorrow. 

 

Have you seen the thread that shows the rest of the measurements? 

 

 

 

[BradKahler 266]

34 minutes ago, ebinmaine said:

 

 

We have a couple Mid Mount Grader Blades here. I can get you those measurements tomorrow. 

 

Have you seen the thread that shows the rest of the measurements? 

 

 

Yes, I found a thread that had most dimensions but I wasn't comfortable trying to figure out the angle.  I used several different images I found and the camera angle seems to distort the angle enough that each image comes up with different angle.

 

Thanks, any help would be appreciate. 

[DLF 2]

The pivot is mounted at 90 degrees to the frame. That angle is determined by the angle the blade is attached to the pivot.

I don't have factory blade to measure. The factory mounted to the top angle of the blade that gave the angle.

Go down to " wheel Horse Manuals" and look up 40" grader blade. It gives good pictures.

 

[BradKahler 266]

3 hours ago, DLF said:

The pivot is mounted at 90 degrees to the frame. That angle is determined by the angle the blade is attached to the pivot.

I don't have factory blade to measure. The factory mounted to the top angle of the blade that gave the angle.

Go down to " wheel Horse Manuals" and look up 40" grader blade. It gives good pictures.

 

 

I agree, the parts manual appears to show what would be a 90 mounting.  I even found one picture that sort of gives that impression.  However, I've found several others t hat are distinctly not 90 degrees to the mounting arm.  Needless to say it's very confusing.

 

 

 

 

 

 

[ebinmaine 78,085]

On 4/10/2026 at 3:12 PM, BradKahler said:

 

 

Upper distance is approximately 16".

Measuring the whole upper frame, from the front, the angled pin sets here. 

 

And the rear cross pin is at 18".

 

 

 

 

Lower distance is 3".

 

 

 

 

Angle is approximately 105⁰. 

 

 

 

 

 

[BradKahler 266]

14 hours ago, ebinmaine said:

 

Upper distance is approximately 16".

Measuring the whole upper frame, from the front, the angled pin sets here. 

 

And the rear cross pin is at 18".

 

 

 

 

Lower distance is 3".

 

 

 

 

Angle is approximately 105⁰. 

 

 

Perfect!!  Exactly what I was looking for.  

 

Thank you.

[ebinmaine 78,085]

19 minutes ago, BradKahler said:

 

Perfect!!  Exactly what I was looking for.  

 

Thank you.

 

 

Glad to help 

[BradKahler 266]

Thanks to the dimensional info from ebinmaine and the information previously posted by others I've made some progress on fabricating the grader blade components.  Other than the block that the lift arm connects to on the main support arm, it's ready to weld together.  The blade itself has previously been fabricated.  I'm currently waiting on the plate that bolts to the blade, I'm having it bent to shape in a fab shop close by.  After that I'll mill the three slots and make the pivot pin.  I'm sure the lift arm won't be exactly like an original, but it should be close enough to function. 

 

  

[ebinmaine 78,085]

32 minutes ago, BradKahler said:

close enough to function. 

 

 

Agreed. 

 

I'm looking forward to seeing your completed project.  

[kpinnc 17,674]

6 hours ago, BradKahler said:

made some progress on fabricating the grader blade components. 

 

Looks factory to me. Well done!