Sunstrand Foot Control

[Racinbob 12,830]

I have posted an ad for a batch of hydro foot controls. I was just asked if they would work on a Sunstrand. As far as I know they are for Eatons only. Most of you know how the control rod hooks up to the shaft to operate an Eaton. Does anyone have a picture of where a Sunstrand would connect? Would it just take a different rod? Or 

[pfrederi 20,012]

Sundstrand motion control movement is vertical..Eaton movement is horizontal

[JoeM 9,653]

Seems as I remember someone having an external setup on a Sunny Strand. ???

[ebinmaine 77,659]

@Handy Don   ?

[oliver2-44 11,284]

Matts Foot Pedal was made for an Eaton

But he would sell it for a Sundstrand and he would buy (extra $$) some part off Ebay (maybe off an Eaton)

I'll  see if I can figure out what it was. 

Edited March 13 by oliver2-44

[midpack 1,114]

On 3/13/2026 at 9:52 AM, JoeM said:

Seems as I remember someone having an external setup on a Sunny Strand. ???

I made one with a clamp on the motion control rod and a pedal from a 269H along with a couple springs to get it to return on its own. Not pretty but it works really well. Its probably been close to a decade but it still goes fine.

[cafoose 3,648]

2 hours ago, midpack said:

I made one

I need to figure one out for a GT-14  I need it because of the FEL 

[oliver2-44 11,284]

Here,the standard parts in Matt’s Pedal Kit. 

 

For a Sundstrand he supplied this part to convert the motion control. 

Can someone confirm the vertical part is added on to a standard Eaton motion controller. 

 

[Handy Don 16,048]

On 3/13/2026 at 10:27 AM, ebinmaine said:

@Handy Don   ?

As you can see from @oliver2-44’s pictures, Matt’s kit took advantage of the existing rocker (Part #11 in this ’95 520-H IPL) by connecting his linkage in the same way that WH did with Part #52 from the column-mounted motion control lever. 

Parts 7-10 and 12-17 comprise the link between the #11 rocker and the Eaton motion control lever atop the transaxle. The rocker supplies “fore and aft” motion to the link. I haven’t seen details (either in person or on an IPL) of how the rocker translates control input motion to the vertical motion that the Sunstrands require. 

 

[pfrederi 20,012]

This is the sunstrand rocker.  I guess if you put a ball end pin in the back of the eaton rocker you could get the vertical motion you need.  I don't see it the picture oh Matts part above.  Also not sure the pivot points are in the same location.

 

 

[Bill D 2,661]

3 hours ago, oliver2-44 said:

Here,the standard parts in Matt’s Pedal Kit. 

 

For a Sundstrand he supplied this part to convert the motion control. 

Can someone confirm the vertical part is added on to a standard Eaton motion controller. 

 

That vertical part is standard.   There is a hole on the rear right corner where you can add a ball stud.

[pfrederi 20,012]

47 minutes ago, Bill D said:

That vertical part is standard.   There is a hole on the rear right corner where you can add a ball stud.

 Are you sure??? ....the ball stud has to come out of the rear of the rocker to hookup with the plastic slider....

[Bill D 2,661]

1 hour ago, pfrederi said:

 Are you sure??? ....the ball stud has to come out of the rear of the rocker to hookup with the plastic slider....

Pretty sure.  There is a hole next to the notch in the rear.  Should be where the ball stud goes.  Only way I can see to make it work.   

 

For the record I only have Eatons in 400 series tractors, and have not done this conversion.  Just trying to help.

[Racinbob 12,830]

 

If that's the hole you're referring to it's not intended for ball stud. The installer has to drill that hole and mount a roller bearing there for the neutral return.

[pfrederi 20,012]

Is there a hole at the Blue arrow that might take the ball stud you need for a Sunstrand...however i don't know would be in alignment with the plastic slider

 

 

[Bill D 2,661]

49 minutes ago, pfrederi said:

Is there a hole at the Blue arrow that might take the ball stud you need for a Sunstrand...however i don't know would be in alignment with the plastic slider

 

 

That's the hole I was referring to in my previous post.

[Bill D 2,661]

Any progress with the conversion?

[Horsin'round 380]

I am the one for whom Bob posted/ inquired. Thank you Bob!

 

All of my projects seem to be long term,  and this conversion would not be an exception.  It is still just a concept. 

 

I  currently have 4, mid 70s tractors, all with running k341s kohlers. Three have sundstrand transmissions one is an 8 speed.  At least 2 are C-160s, the other two are probably mutts, haven't really tried to vett them. 

 

One of the mutts,  has a leaky axle seal. I've made a couple of attempts at replacing the seal,  with no luck.  There seems to be a small ridge of metal in the casing that prevents the seal from being seated. I need to get the transmission off the tractor and onto the workbench to assess. If that goes well. This is the one I intend to modify.  

 

Like I said,  it's a long term project,  and will take me a while to get there.  I always seem to have a lot on my plate. 

 

My thought was to attach a tab to the sundstrand rocker, but replacing it with the Eaton rocker makes perfect sense.  These little nuggets of knowledge are priceless.  

 

I would love to here more,  possibly from someone who has made a successful conversion.