520H test and tune

[sqrlgtr 2,191]

Finally got a chance to look at the 520H I brought home a week or so ago. Took breather off and safe to say PO probably hadn’t done to much preventative matainence. Taped throat up on carb and got rid of the big chuncks. Threw battery on and fired right up but has to have just a hint of choke on to not have a surge. All gauges and idiot lights seem to work but voltmeter shows just a little under 12 volts and when you unhook ground on battery it dies? Thought I would try some B12 in fuel before getting to serious on carb rebuild, might get lucky might but doubt it. Did drive around for a little while and man does that twin flat head hum no smoke knocks or weird nosies and has plenty of power. Trans seems good and stout but wants to creep backwards.

[ebinmaine 77,432]

11 minutes ago, sqrlgtr said:

carb rebuild

 

I've done one of these for @JCM  

Pretty straightforward.  

I did not remove the carb or reinstall though. I believe there's a procedure for the intake manifold.  

 

 

13 minutes ago, sqrlgtr said:

wants to creep backwards.

Hopefully just an adjustment.  

 

 

 

13 minutes ago, sqrlgtr said:

Did drive around for a little while and man does that twin flat head hum no smoke knocks or weird nosies and has plenty of power. Trans seems good and stout

 

 

Excellent! 

[ri702bill 11,297]

No worries - it just has its winter coat on...!!

 

[JCM 10,773]

A few pics for you. The 520's seem to be the most abused of ALL WH tractors out there. Why. I have no idea. Keep at it, you will get there.

[Handy Don 15,976]

55 minutes ago, sqrlgtr said:

when you unhook ground on battery it dies?

On non-magneto tractors, the battery powers the coil for ignition. The current goes out of the battery via the “red” wires and to the coil. If you disconnect the battery ground, those poor little volts cannot find their way home to complete the circuit!

Edited 3 hours ago by Handy Don

[lynnmor 8,638]

How many hours are on the tractor?  It may be due or overdue for a valve adjustment.  If it has over 750 hours on it then adjusting the valves is due and doing that will have you pulling the exhaust and intake which is a good time to do a carburetor cleaning and some other needed maintenance.  Do not continue to run the engine hard with a lean mixture caused by a dirty carburetor unless you want to join the loose valve seat club.  Let us know if you want to do a proper valve adjustment and carburetor cleaning and we can outline the needed work.

[Handy Don 15,976]

1 minute ago, lynnmor said:

unless you want to join the loose valve seat club

Lynn, you've given me an idea for some more clubs!

Stuck Hub

Stuck Steering Wheel

Stuck Hitch Pin

No Balance Gears

Patina

and many more...

 

[sqrlgtr 2,191]

26 minutes ago, lynnmor said:

How many hours are on the tractor?

A little over a 1000 and supposed to be correct???

 

28 minutes ago, lynnmor said:

Let us know if you want to do a proper valve adjustment and carburetor cleaning and we can outline the needed work.

Yeah main objective today was just run it around a bit just to see what I did have, believe everything is pretty solid and she just needs a little TLC. Ordered carb kit today and plan was to take top off carb and clean up best I could but agree valve adjustment wouldn't be a bad idea. What gaskets and stuff would I need to have on hand before I tackled a valve adjustment? I was also surprised at the ground speed it had. Seems a lot faster than a 6/8 speed tractor to me. Hydraulics seems real stout also. From the looks of the turf on that carb, I can't imagine what the cooling fins looks like .

[kpinnc 17,216]

2 hours ago, sqrlgtr said:

little over a 1000 and supposed to be correct???

 

At that point you need to decarbon the heads anyway. To get there, the intake manifold and exhaust will have to be removed so a valve adjustment is easy at that level of disassembly. 

 

But- a properly cared for Onan can last literally thousands of hours. It's worth it.