K181 ticking sound

[gt14rider 1,020]

Started pulling this apart about end of August, just got it in the basement, pulled the engine apart, too 

have a look see. (See video )

 

Found it.

 

think I have a nother cam around here 

 

Edited yesterday at 03:47 PM by gt14rider

[ri702bill 10,983]

Hmmm. is the cam the source of the problem or is it the victim here??

Did you break the connecting rod?? I ask because I bought two C81's years ago. One ran but was tired; the other broke the connecting rod, snapped the cam in two and blew out the back cam mount. And ventilated the block bigtime. I did save the head, flywheel, tins, oil pan , points & coil though...

Edited yesterday at 05:52 PM by ri702bill

[gt14rider 1,020]

Hi all @ri702bill , rebuilt that k181 in spring of 2018, put it together with a bunch of parts, so could be it was cracked when installed, it all ways had a tic, but not bad enough to pull apart,  the dreaded kohler tic.  Anyway got to dig up another cam. 

[gt14rider 1,020]

Got it apart, what you think?  A little JP Weld might work. Got a cat scan done, confirmed, cam fubar.

[pfrederi 19,505]

Love the CAT scan

[kpinnc 16,642]

Cat scan.

 

...I'm using that one! 

[gt14rider 1,020]

Yah she's a humdinger, she has to be right in the middle everything. 

 

Found the camshaft, cleaned it up, should work.  Will clean up the block, new gaskets,  couple seals, I already rebuilt the fuel pump, and carburetor. Had to make bushing NLA, come out great, new shaft and made some foam gaskets out of a pre air filter .

[WHX?? 53,797]

What is the blue stuff on the fuel pump? 

Nice job on the bushing maybe we can make them now @Achto

Always thought a o-ring on the shaft wouldn't hurt. 

[Achto 30,505]

10 minutes ago, WHX?? said:

Nice job on the bushing maybe we can make them now

 

Shouldn't be too difficult.

 

[gt14rider 1,020]

@WHX?? the blue is magic marker, poor man's Persian blue. Put it on sandpaper on glass, check the high spots

[WHX?? 53,797]

15 minutes ago, gt14rider said:

poor man's Persian blue

Thought maybe it was a bluish Permatex sealer I tried once that did't work. 

We was just talkin about glassing pumps.

Good trick ... gonna  those pics for my fuel pump instructional.  

I always misted them with a rattle can like a head but the mist can go where you don't want it to. 

Edited 16 hours ago by WHX??

[WHX?? 53,797]

9 hours ago, ri702bill said:

other broke the connecting rod, snapped the cam in two and blew out the back cam mount.

Yep been there done that ...  guy at plow day said he checked his oil ... bull roar. Nothin but sludge in the pan.  Got extremely lucky and only busted the cam. Never even bent the cam axle. 

Can't believe it ran with only a tic Rider. 

Edited 15 hours ago by WHX??

[gt14rider 1,020]

 @WHX?? I don't think it was broken al the way,  in the video you can see a chunk out of the cam,but it didn't break till I took the cam pin out. This was in the pan. It ran when it was parked. Lasted 8 years 

[WHX?? 53,797]

3 minutes ago, gt14rider said:

broken al the way, 

Ahhh 

Can't see the vid my internet too slow and sucks. Especially with vids. 

Edited 15 hours ago by WHX??

[gt14rider 1,020]

Here's a picture of cam

[WHX?? 53,797]

Good thing that chip didn't go through the timing gears.