Got another one. A 416 this time.

[cleat 7,820]

Parking brake cam plate assembly ready to be installed.

 

Parking brake cam plate installed.

Pivot point was lightly greased.

 

[cleat 7,820]

Brake rod assembly ready to install.

 

Brake rod just inserted into parking brake cam and return spring installed.

Rod was greased where it inserts into cam plate.

 

Rod fully inserted into cam plate then washer and clip installed.

Note the smaller clip, the one shown earlier was causing interference with the cam plate bolt.

 

Brake return spring with rod fully installed into cam plate.

 

Brake spring and bolt assembly ready to install.

There should be 3 washers, only two are shown in this picture.

 

Brake spring assembly installed just finger tight.

I will set this later on when parking brake latch is installed.

 

Brake pedal ready to install.

 

Tractor ready to accept brake pedal.

 

Brake pedal installed.

 

Overview of complete brake system.

 

 

[cleat 7,820]

Hydro cam follower arm ready to install.

 

Hydro cam follower arm installed.

I put a tint bit of never seize on the male threads but kept the taper dry.

Nut tightened by hand (I was afraid an impact would over tighten and possibly crack the arm on the taper) while holding the arm so as not to break anything in the hydro unit.

 

 

[cleat 7,820]

Hydro speed control cam plate assembly ready to install.

This machine will have foot control so no tension washers are needed.

Instead, I punched out some Teflon washers so cam plate will pivot freely.

 

Hydro speed control cam plate spacers installed onto studs.

 

Hydro speed control cam plate lower washers installed.

 

Hydro speed control cam plate sat into place.

 

Hydro speed control cam plate bushing greased and ready to install.

I also put a little never seize on the studs.

 

Hydro speed control cam plate upper washers and bushing installed.

 

Hydro speed control cam plate locknuts installed.

Nut on bushing stud was firmly tightened.

Nut on washers was just turned in until there was little to no free play but the plate will pivot side to side freely.

 

Hydro speed control eccentric cam ready to be installed.

 

Hydro speed control eccentric cam installed and rotated so large side faces the long slot on the cam plate as per the manual.

Bolt tightened.

You will need a 1" and a 1/2" wrench to do this.

 

Tractor overview as of today.

 

Edited yesterday at 04:43 PM by cleat

[ebinmaine 75,180]

9 hours ago, cleat said:

Hydro cam follower arm 

 

 

@JCM has one of these on a rebuilt transmission that's broken basically in half. 

How does that get removed from the transmission? 

Special puller?

 

 

[cleat 7,820]

2 hours ago, ebinmaine said:

 

@JCM has one of these on a rebuilt transmission that's broken basically in half. 

How does that get removed from the transmission? 

Special puller?

 

 

 

I just loosen the nut a few turns and then use a small 2 jaw puller.

Once it pops free of the taper it should just lift off once the nut is removed.

 

Do not pry on it or force it in either direction loosening or tightening the nut as internal transmission damage could occur.

 

 

 

[cleat 7,820]

Fuel tank supports ready to be bolted to fender support bracket.

 

Fuel tank supports and fender support bracket laid down flat on the front side.

Bolts all loosely installed after getting a smear of never seize to prevent galling (these are SS bolts).

 

All 4 bolts torqued to 17 ft/lb.

 

[cleat 7,820]

Fender bracket assembly ready to install.

Note the liquid Teflon sealant used on the bolt threads to keep water out and oil in.

Do not use Teflon tape as bits of it may end up in the hydro unit causing issues down the road.

 

Tractor ready to receive fender bracket.

 

Sealant was applied to the bolts ensuring there is none on the end of the bolts to get into the transmission.

 

Fender bracket sat into place then the bolts were screwed in finger tight.

I then measured between the fender bracket and the hood stand on both sides and fender bracket was moved until the measurements were the exact same on both sides.

There is just enough free play in the bolt holes for a bit of adjustment.

This should ensure the fender bracket is square and even. 

 

Fender support bots were torqued to 26 ft/lb.

 

Tractor as it sits today.