-
Similar Content
-
By Southern_Secret
Hello fellow Horse Heads long time no post for me, life gets crazy & a lot of things change sometimes but anyhoo. So back a few years ago when I first got my 1994 314-H I had it at my shop going threw it. One of my customers walk past as im working and said, you know I think Iv got a Wheel Horse & im thinking "no you dont buddy". I give him my # to send pics thinking it was a big waste of time & after getting the pics I realized he did have a Wheel Horse! I hand shake bought it right there, asked him to bring it to my store & he said no problem. Well after almost 2 years it is finally in my orbit. I know very little about it other than his father-inlaw got it new and used it around his house moving snow and stuff. His father inlaw moved down south here when his daughter got married and gave the tractor to my customer because he had a farm & his the inlaw had no use for it anymore. Same with every barn find, "it was running when parked" 8 years ago, said one of the axel seal is leaking. Im happy and hope I can get it back in running order soon cause it is going to be handy around the truck farm!!
I will post Pics as soon as I reinstate my membership
-
By Swemill
Hi everyone!
Long time since i was here and my old pics is gone from the forum.
I just uploaded a movie with pics on youtube, and thought i could share it for you guys.
I would love to get some comments on my Youtube channel, from you true Wheel Horse fans!
Thanks and Best Regards
-
By Brandon Byers
I know I'm half a year ahead of schedule!
I picked this 1974 D-180 up early last year. It had a pretty hard life, and the previous owner gave his best attempt at keeping it alive. Hydro was strong so I serviced it and put it to work mowing all year. I decided if it would make it through the season then it would get some TLC. By fall it was burning about a quart of oil an hour but it made it. I have no clue how many hours are on it, every hole, bushing, bearing on this tractor is pooched. If you look closely, somebody used two 1" NPT Pipe Flanges to rebuild the mounting points for the upper 3 point cylinder. Hey it works!
I rebuilt the steering gearbox and re-bushed the front axle along with making new spindles.
I had the 482 Kohler bored .20 over (it was .10 over already) and gave it a rebuild with the intention of putting it back to work on snow duty.
I then dawned on me that this tractor will be 50 years old next year - and these old D's are becoming harder and harder to find anymore. So I decided to customize it a bit and go for what a maybe a dealership would offer for a 50th anniversary model if Wheel Horse was still in business today (In another universe, maybe!)
As D's aren't known for their looks - and I can't leave anything alone. I took approximately 2 Inches out of the grille and bezel.
I updated most of the wiring and lights. Gave it a new set of Carlisle Ags along with Vredestein front ribs. It got a new seat and I painted all the accents aluminum.
I patched, rebuilt the 48" deck and put new blades, wheels, and hardware on it. The Blade & 3 point scoop somebody adapted to it also got some attention.
Lastly I stripped it most of the way down and painted it with IH red acrylic urethane enamel.
I always forget to take pictures during my projects but here's a few:
Before:
After:
Thanks for reading!!
-
By jmack
I'm needing the o-ring sizes for my control valve assembly to my D-180. Does anyone have a list of these or the McMaster Carr part numbers?
Thanks,
Jonathan
-
By Sarge
What started out as a simple task of moving my 6-1/2' x 12' utility trailer to unload it's contents back into the Shed Repair Project after building a new floor turned out to be a really bad day . I figured the weight of the trailer and it's load was probably around 2,500lbs or more and the big D-180 should be able to handle it . Used the 3pt hitch and an adapter to lift the trailer tongue and off I went...until I got to the end of the north drive and the pump coupling on the hydro failed - badly . In hindsight - the trailer probably weighed closer to 4,000lbs the way it felt behind the truck ...
Now , the trailer had to be taken off the tractor and put on it's jack ....which didn't work out too well loaded that heavily . Since the trailer was built with 2x3 angle iron on the tongue it decided to fold itself into a pretzel - despite the wheels being blocked tight so it couldn't move . It fell over and I had to use the HI-Lift to get it off the ground . The sight of the trailer falling over in the rear view camera on the Dodge is still well embedded in my memory - I knew that was going to be another large project .
The coupling had an earlier repair from last winter's failure - so a pto pin was driven through the hole to get it out back to my work area to be fixed later . It made the short trip , but just barely and the tow valve was frozen tightly . As it turned out , the damage to the D was a much bigger issue..and cost 3 times as much in total .
The pic doesn't do the damage any justice - that entire tongue was bent badly -
Sand blasted , new tongue built and waiting for paint -
Painted , as it sits now awaiting the lights , wiring and re-install the floor decking .
All the while - got more work done on the D's pump problem . Found a great used pump , as well as a spare coupling in good shape . After a lot of machine work ($$$) we came up with a solution and everything was back together...
After all this I found that both the original mufflers were completely shot and falling apart - so another project ...
Bought a pair of 180* mandrel bends , two cone transitions and a pair of @jimkemp 8" mufflers (very nice, btw) . Fabricated the flanges for the engine's exhaust ports , as well as the pipes for the stacks -
Spent a lot of time rolling the engine over on the starter to slowly prime the pump back up and finally , after several months - fired Big Ugly to test the exhaust before painting the stacks . No leaks from the hydro thanks to some new o-rings and backer rings from @pfrederi on the hydro manifold , that was a big relief .
A bit shocked at the sound of the big opposed twin - somewhat like a Harley running on the choke or something - but overall not obnoxious or too loud ....
D180 startup.mp4
If you don't want to wait for the MP4 to load - here's the YouTube link -
I don't think the camera's microphone will show the sound too well , but so far I like it . Took a ride around the block , nice having this beast back up and running , finally . Now to finish that dumb trailer....pretty much wasted nearly the whole summer getting all of this done plus the hours at work . I'm about ready for a break but need to get ready for winter .
Sarge
-