Wild Bill 633 770 #26 Posted March 9, 2022 @jeepdan, I have a set of loose 520H spindles and can make a detail drawing for you if still needed. The drawing would be a LH shown, RH opposite drawing. Unfortunately, I am not be able to start the drawing until as least this weekend. Please advise if you are still in need. 1 Share this post Link to post Share on other sites
Handy Don 10,607 #27 Posted March 9, 2022 1 minute ago, Bill633 said: @jeepdan, I have a set of loose 520H spindles and can make a detail drawing for you if still needed. The drawing would be a LH shown, RH opposite drawing. Unfortunately, I am not be able to start the drawing until as least this weekend. Please advise if you are still in need. Just to note here that he is looking for dimensions for the swept axle, 1" spindles. Share this post Link to post Share on other sites
Wild Bill 633 770 #28 Posted March 9, 2022 1 hour ago, Handy Don said: Just to note here that he is looking for dimensions for the swept axle, 1" spindles. That is what I have, 1" spindles. 1 Share this post Link to post Share on other sites
jeepdan 321 #29 Posted March 10, 2022 (edited) 10 hours ago, Bill633 said: @jeepdan, I have a set of loose 520H spindles and can make a detail drawing for you if still needed. The drawing would be a LH shown, RH opposite drawing. Unfortunately, I am not be able to start the drawing until as least this weekend. Please advise if you are still in need. Thanks very much Bill. I think that I now have it all figured out. If I run into a question I will get in touch. Thanks to everyone! Dan Edited March 10, 2022 by jeepdan 1 Share this post Link to post Share on other sites
jeepdan 321 #30 Posted March 12, 2022 On 3/4/2022 at 7:36 AM, Pullstart said: I’m right here fellas! @jeepdan the tape is for alignment. My eyecrometer took care of the rest. I just had a third party accurately measure the tie rod hole distance for me. Pull's eyecrometer was almost spot on 1 1 Share this post Link to post Share on other sites
Pullstart 59,733 #31 Posted March 12, 2022 I’ve done this stuff a time or two 1 Share this post Link to post Share on other sites
WHX?? 46,797 #32 Posted March 12, 2022 29 minutes ago, Pullstart said: I’ve done this stuff a time or two What git blind outhouse lucky!?!? 2 Share this post Link to post Share on other sites
jeepdan 321 #33 Posted March 13, 2022 (edited) This is what I have come up with so far. Nice thing is that a person can replace the 1" kingpin in the future if needed to. Edited March 13, 2022 by jeepdan 2 2 Share this post Link to post Share on other sites
jeepdan 321 #34 Posted March 19, 2022 After boring the tapered holes for the tie rod studs, I welded the steering arms on. 2 2 Share this post Link to post Share on other sites
jeepdan 321 #35 Posted March 19, 2022 (edited) Kind of close, but I was able to maintain 36.5" to the outside of the 4" wide wheels. Waiting on the 4.00-8 Deestones to arrive. Edited March 19, 2022 by jeepdan 3 4 Share this post Link to post Share on other sites
WHX?? 46,797 #36 Posted March 19, 2022 Oh now that is just Sawwweeeet Dan You didn't tell us you were a master machinest.. you da boss & absolutely top notch work ! Share this post Link to post Share on other sites
Pullstart 59,733 #37 Posted March 19, 2022 What a work of art! You make it look easy! 1 Share this post Link to post Share on other sites
SylvanLakeWH 24,151 #38 Posted March 19, 2022 (edited) On 3/3/2022 at 7:43 PM, WHX?? said: Gotta know him to love him Jeep......he's like that neibors dog that pees on yer bushes but so cute & friendly ya still gotta scratch him behind the ears.... Really? And… beautiful work @jeepdan!!! Edited March 19, 2022 by SylvanLakeWH Share this post Link to post Share on other sites
