Jump to content
Jeff_B

36" deck mower bearing assemblies

Recommended Posts

Jeff_B

Where's your go-to source for QUALITY 103119 bearing shaft assemblies? Also, I don't have my deck apart yet, but seem to remember they're tough to remove from the housings. Any tips or tricks? Finally, just recently I've had a couple of  the center bearings go loose on two different decks. Once is one thing, but twice? More than a coincidence? Should I be releasing tension on the belt by loosening the mule drive when not in use? We've had WH tractors for over 40+ years and I've never done that before! THANKS in advance! 

Share this post


Link to post
Share on other sites
 
peter lena

@Jeff-B , found these , just looking around , would also wonder if they are built with HI TEMP GREASE. like a polyurea , that will stay with it , never had a bearing go loose , but have had bearing lubrication failure ,in the past, pete

  • Like 1

Share this post


Link to post
Share on other sites
 
gwest_ca

Share this post


Link to post
Share on other sites
 
Rfp55

If you have double D cast belt pulleys heating may help them pull off. Don't put a gear puller on pulley rim or you'll be welding pieces. Just bought 3 and installed, parts were $58 and prob 15 shipping as two vendors were involved. One bearing was a new/old stock toro, other two were Stens - and every bit as good. New lock washers on top end of shaft or they may loosen up. Pretty easy job compared to Simplicity or Ariens deck, and marvelously Quiet when engaged after you're done. Its only about 20 years to wear out so it should be good for awhile unless you are moving rough junk, stumps and rocks.

  • Like 1

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • cbj75
      By cbj75
      I have a 1975 D200 Wheel Horse with front mount dozer blade, package includes Wheel Horse Dump Trailer, 48" belly mower side discharge, Wheel Horse front and rear wheel weights, turning brakes, rear PTO and 3-point to 2" receiver attachment, and Brinley twin disc harrow. Rear luggage/rack carrier, All refurbished, sandblasted and painted Ford red in 2016. Lots of extra Wheel Horse parts included.
       
      Package price $3000.00.
       
      Bryce Johnson
      102 Anglers PT
      Mc Cormick SC 29835
      913-638-6788

      IMG_1962.HEIC IMG_1965.HEIC IMG_0279.HEIC


       
    • Joe Warren
      By Joe Warren
      Mower Spindle Components
      mostly new old stock
      Prices shown do not include the cost to ship.
      Message me with your needs and any questions.
      Thank you.
      Joe
       
      PART NUMBER(S)
      DESCRIPTION
      QTY. AVAILABLE
      PRICE EACH
      103711
      NOS Spindle shaft assembly
      1
      39
      103711 (used)
      Used spindle shaft assembly
      1
      29
      101686 or 5875
      NOS Spindle shaft sub-assembly
      1
      49
      104890
      NOS Spindle shaft
      1
      49
      104982
      NOS Spindle shaft
      1
      44
      107998 or 107446
      NOS Spindle shaft
      2
      89
      109912
      NOS Spindle shaft
      1
      59
      112673 or 109965
      NOS Spindle shaft
      1
      59
      108849
      NOS Spindle shaft
      1
      89
      102780 or 104373
      NOS Spindle cups 1.0” tall
      2
      39
      ??????
      NOS Spindle cups 0.9” tall
      2
      39
      102784 or 104374
      NOS Spindle cups 0.8” tall
      1
      39
       
       
       
       
      100289
      NOS Needle bearing, MFD USA Torrington
      2
      19
      101411
      NOS Ball bearing, sealed both sides, MFD China
      2
      29
      101480 or 1515 or 5493
      NOS Ball bearing, sealed both sides, MFD China
      6
      9
       
       
       
       
      106084
      NOS Ball bearing, sealed one side, MFD Japan
      11
      9
      106085
      NOS Ball bearing, open, not sealed, MFD Taiwan
      16
      9
       
       
       
       
      106070
      NOS Seal spacer
      10
      9
      100674
      NOS Spacer-pulley
      1
      13
      107445
      NOS Spacer-bearing
      1
      9
      106069
      NOS Spacer
      1
      9
       
       
       
       
      110234
      NOS Lock bolt-pulley
      4
      2
      110242 or 908033
      NOS Lock bolt-blade
      11
      2
      915090 or 32146-20
      NOS Lock nut-pulley
      11
      2
      936028 or 32120-42 or 52-6640
      NOS Snap ring
      7
      2
      8389
      spindle housing
      1
      39




    • Upnorthman
      By Upnorthman
      314-8 In great shape. Used for mowing more than anything. Bought it a few years ago but got a new tractor. I used the blower very little and it sounds like it needs a bearing on it. Runs well. I have new chains I've not put on yet and extra belts. 








    • Joe Warren
      By Joe Warren
      one NOS 106846 right drive pulley, mower deck, used on double D style shaft, replaces part 5877, $55 includes shipping within US lower 48


    • ryobi.warrior
      By ryobi.warrior
      The belt on my Wheel Horse 314-8 mower deck (05-37SC01) appears to be contacting the deck bracket between the spindle pulleys. I am a novice when it comes to Wheel Horse maintenance (at best), but this does not seem correct.
       
      I recently inherited this Wheel Horse, so I do not know the maintenance history. Unfortunately, the mechanic who previously worked on it was a no-show for a scheduled maintenance visit.
       
      Any advice on how to address this? Thanks in advance... this seems like a great forum and I'm looking forward to spending time here!
       
      Photos (please forgive the dirt and grime, I plan to clean it up!): https://imgur.com/a/4PknZuJ




×
×
  • Create New...