Sparky-(Admin) 23,147 #2951 Posted April 26 Freshly painted wheels 7 8 Share this post Link to post Share on other sites
TonyToro Jr. 1,962 #2952 Posted April 26 C-121 with the 36” RD deck 7 4 Share this post Link to post Share on other sites
c-series don 10,024 #2954 Posted April 27 @AlexR I really like your wheel weights especially the front. I’ve never seen any like that before. 1 1 Share this post Link to post Share on other sites
AlexR 1,853 #2956 Posted April 27 14 minutes ago, c-series don said: @AlexR I really like your wheel weights especially the front. I’ve never seen any like that before. Thanks they were on the Raider 10 I grew up on. Looks like homemade 1" thick plate steel cut with a torch, or plasma cutter. We didn't do that, it came with the tractor when my parents bought it. They are stacked double on both sides. 4 2 Share this post Link to post Share on other sites
WHX?? 51,739 #2957 Posted April 27 I like the seat on the plow mule @AlexR 1 1 Share this post Link to post Share on other sites
Sparky-(Admin) 23,147 #2958 Posted April 27 1 hour ago, c-series don said: @AlexR I really like your wheel weights especially the front. I’ve never seen any like that before. Don, I’ve used these steel pipe flanges on the front wheels in the past (hard to see in the grainy pic) double stacked. I’ve also hung those same pipe flanges under the frame up front. 4 3 Share this post Link to post Share on other sites
ebinmaine 72,654 #2959 Posted April 27 18 minutes ago, Sparky said: pipe flanges What size are those? Share this post Link to post Share on other sites
Sparky-(Admin) 23,147 #2961 Posted April 28 2 hours ago, ebinmaine said: What size are those? If I still have them I’ll measure one up tomorrow for ya. I suspect they were on the tractor when I sold it though I might still have one or two kicking around. 2 Share this post Link to post Share on other sites
AlexR 1,853 #2964 Posted May 3 Added another tractor to the picture. 4 5 Share this post Link to post Share on other sites
Sparky-(Admin) 23,147 #2965 Posted May 3 Side shot from today’s show … 3 8 Share this post Link to post Share on other sites
Macgyver 109 #2967 Posted May 4 This one is one of 3 that I have and getting ready for it's first show in a couple weeks 4 5 Share this post Link to post Share on other sites
Achto 29,394 #2969 Posted May 4 (edited) After a long winter's rehabilitation. Edited May 4 by Achto 3 12 Share this post Link to post Share on other sites
Thegearhead0324 1,352 #2972 Posted May 23 The ol 1257….. I moved it to clean in the shed a bit. I definitely regret selling the sickle bar back in the fall time, I’m having “seller’s remorse”. Hopefully another comes my way someday. 3 3 Share this post Link to post Share on other sites
Sparky-(Admin) 23,147 #2973 Posted May 23 On 4/27/2025 at 7:39 PM, ebinmaine said: What size are those? @ebinmaine A month later I’m replying . Not sure how these are sized. But I suspect it’s by the size of the hole thru the center. 1 Share this post Link to post Share on other sites
Ed Kennell 41,956 #2974 Posted May 23 3 hours ago, Sparky said: . Not sure how these are sized. But I suspect it’s by the size of the hole thru the center. If that is a NTP bolting flange, the thread is probably 2" NPT. The small end of 2" NPT is around 2.1" and the large end is 2.3. 1 1 Share this post Link to post Share on other sites
Macgyver 109 #2975 Posted May 24 (edited) This is a pair of tractors you don't see every day. To see a 520-8 and a C195 in the in the same heard is rare. Edited May 25 by Macgyver Had to correct a mistake. 7 1 Share this post Link to post Share on other sites
