ebinmaine 76,503 #3076 Posted September 1, 2025 1 13 Share this post Link to post Share on other sites
Sparky-(Admin) 24,237 #3079 Posted September 7, 2025 The only machine I own that lives in my house, in the basement to be exact (not my living room!) 2002 315-8 5 3 4 Share this post Link to post Share on other sites
ebinmaine 76,503 #3080 Posted September 7, 2025 19 minutes ago, Sparky said: not my living room! Why not??!!?? 2 Share this post Link to post Share on other sites
Sparky-(Admin) 24,237 #3081 Posted September 7, 2025 1 hour ago, ebinmaine said: Why not??!!?? Access to the living room is not ADA compliant …AKA, no ramps 2 Share this post Link to post Share on other sites
adsm08 3,979 #3082 Posted September 7, 2025 1 hour ago, Sparky said: Access to the living room is not ADA compliant Guess I can't go into your living room then. 1 Share this post Link to post Share on other sites
Pullstart 68,610 #3083 Posted September 7, 2025 1445 helping finish some sand work before forms and grade are set… 5 4 Share this post Link to post Share on other sites
pfrederi 19,460 #3084 Posted September 7, 2025 GT-14 getting ready to haul away birch tree 9 Share this post Link to post Share on other sites
Pullstart 68,610 #3085 Posted September 14, 2025 5 1 Share this post Link to post Share on other sites
ebinmaine 76,503 #3086 Posted September 14, 2025 @Pullstart Boat seat and dual tanks?? Share this post Link to post Share on other sites
ebinmaine 76,503 #3087 Posted September 14, 2025 Couple of full line side shots from the Meet n Greet in N Berwick yesterday. 3 8 1 Share this post Link to post Share on other sites
ebinmaine 76,503 #3089 Posted September 14, 2025 Working on the woods today! 2 10 Share this post Link to post Share on other sites
MainelyWheelhorse 2,290 #3090 Posted September 14, 2025 Today’s progress after work. The hood is hand tight bolted, the rear fenders are sitting on the gas tank bracket, the front spindles and tires are held in by gravity. But the rear end is bolted in along with the rear tires and fender/gas tank bracket. Progress! 5 2 Share this post Link to post Share on other sites
Pullstart 68,610 #3091 Posted September 15, 2025 14 hours ago, ebinmaine said: @Pullstart Boat seat and dual tanks?? The engine mounted tank had to go. It had to allow the engine to slide back another inch and a half or so. The boat seat is super comfy! 3 Share this post Link to post Share on other sites
Horseoholic 258 #3092 Posted September 20, 2025 Started some early fall trimming. 6 3 Share this post Link to post Share on other sites
Sarthurs01 1,024 #3093 Posted September 21, 2025 Getting his Lawn Ranger cleaned up and ready to polish. Got to love saving some original paint! 4 8 Share this post Link to post Share on other sites
Sparky-(Admin) 24,237 #3094 Posted September 27, 2025 Did a little clearing work behind the shed. Weeds and debris were taking over. Not sure what the plan is for this spot just yet. 6 3 Share this post Link to post Share on other sites
Teddy da Bear62 168 #3095 Posted September 27, 2025 I see a fenced area and lots of ducks...... 1 Share this post Link to post Share on other sites
midpack 1,084 #3096 Posted September 27, 2025 Doing some work yesterday 6 3 Share this post Link to post Share on other sites
Bar Nuthin 2,041 #3097 Posted September 27, 2025 Might be adding some horses to the stable today. We'll see! 2 4 Share this post Link to post Share on other sites
ebinmaine 76,503 #3098 Posted September 27, 2025 3 minutes ago, Bar Nuthin said: Might be adding some horses to the stable today. We'll see! Wwhhaatt?? 1 1 Share this post Link to post Share on other sites
MainelyWheelhorse 2,290 #3099 Posted September 27, 2025 (edited) I got the herd out yesterday. Edited September 27, 2025 by MainelyWheelhorse 3 2 Share this post Link to post Share on other sites
sqrlgtr 1,782 #3100 Posted September 27, 2025 Little pm going on at the Wheel Horse Barn. 2 1 Share this post Link to post Share on other sites
