ebinmaine 63,140 #2151 Posted April 15, 2019 That seat ain't nothing a little gorilla tape won't fix... 2 1 Share this post Link to post Share on other sites
RetroMower 333 #2152 Posted April 16, 2019 2 hours ago, ebinmaine said: That seat ain't nothing a little gorilla tape won't fix... For the time being gorilla tape will do but it wont help i can feel the bolts in "my" seat I am very much looking forward to the seats Bob Ellison are making. Hope i can snag a set st the show 4 1 Share this post Link to post Share on other sites
Ralph S 342 #2153 Posted April 16, 2019 It was a bitter sweet past Sunday. I sold the 518H that I had transplanted an 1100 series transaxle in. I hated to see it go down the driveway but the cash gave me a worm fuzzy feeling . I realized then, that I have room for one more ! 2 3 Share this post Link to post Share on other sites
squonk 38,929 #2154 Posted April 16, 2019 Replaced the brake shaft seal on HHHOOOWWWAAARRRDDD!!! today. 6 Share this post Link to post Share on other sites
Aldon 4,826 #2155 Posted April 16, 2019 5 minutes ago, squonk said: Replaced the brake shaft seal on HHHOOOWWWAAARRRDDD!!! today. Mike, did you warm your hands before messing with Howard’s rear seal? 8 Share this post Link to post Share on other sites
WHX?? 46,775 #2156 Posted April 16, 2019 Betcha Howard would get a kick outta that one Aldon! 4 Share this post Link to post Share on other sites
dclarke 4,011 #2157 Posted April 17, 2019 Put the battery back in the 701 and brought it out of hibernation. What a beautiful spring day today. 3 11 1 3 Share this post Link to post Share on other sites
Ralph S 342 #2158 Posted April 18, 2019 I installed the belt gaurd and fabricated front weights for the 520 HC today. I'm ready to go plow now 1 1 Share this post Link to post Share on other sites
WHX?? 46,775 #2159 Posted April 18, 2019 Nice seat cover ther Ralph. ..Denny @dclake1971 is that my new dibs tractor? You bring that to AJ's there's gonna be drool on it! 2 Share this post Link to post Share on other sites
Ralph S 342 #2160 Posted April 18, 2019 1 minute ago, WHX22 said: Nice seat cover ther Ralph. ..Denny @dclake1971 is that my new dibs tractor? You bring that to AJ's there's gonna be drool on it! I had it sitting out in the rain the other day and covered the seat cause there are a lot of rips in the seat. When I hit the Powerball I'll get a new seat. 😆 4 Share this post Link to post Share on other sites
ohiofarmer 3,157 #2161 Posted April 18, 2019 Mowed the lawn and when I came out to finish after supper, the throttle cable broke. All in all it was a good day as the 1056 did a good job with the engine out for a first test with plenty of power. This tractor only cost a shade over a c note 3 Share this post Link to post Share on other sites
Lee1977 6,217 #2162 Posted April 18, 2019 I was using the 312-8 to spread some piles of rotted leafs over the garden. I bought it from Wheel-it back in July 2014. It was a father and son project at some time before he bought it for the engine. He was wanting a Magnum 16 and it was a 12. It was a collection of mixed parts not sure the model best guess is 88 or 89. The hood was bent up a few places but it had a professional paint job some time earlier. the fender had never been painted It had a 1/2" drive belt on it and It did alright so I left it on. It also had the belt run a little different so I fix that. This is the way it was when I got it. I have used it a couple of times lately and It has want to jump in reverse. I have a used 5/8" drive belt so I decided to put it on. I found this when I took it apart. Never seen a belt guard welded to the PTO bracket. I prized it up to allow a little clearance for the 5/8" belt. I had though the belt running over the top of the 3/4" bar was why the back of the 1/2" belt was worn, but it was the belt digging into it. There were other thing welded in place on this tractor, the hood hinge pin, and the roll pin in the loop bracket. 2 Share this post Link to post Share on other sites
ebinmaine 63,140 #2163 Posted April 20, 2019 As we were clearing out trees for the new Horse stable I cut one that leaned over onto others. We used the Cinnamon Horse to drag it a few feet so we could finish cutting. Fantastic torque from the big K341. Note that I had forgotten to raise the engine RPM. That pull was done at IDLE. Imagine how it'll go with a little more appropriate engine spin... 1 2 Share this post Link to post Share on other sites
TonyToro 1,032 #2164 Posted April 20, 2019 (edited) Fabricated a pulling hitch for my sons tractor. We had to make a Cub Cadet work on the Wheel Horse. Next is to make wheelie bars. Edited April 20, 2019 by TonyToro 1 Share this post Link to post Share on other sites
The Tuul Crib 7,332 #2165 Posted April 21, 2019 (edited) Slowly getting the parts put back on this little beast of a tractor. I’m ready to start mowing with it any day now! SEAT TIME !!! Edited April 21, 2019 by The Tool Crib 3 7 1 Share this post Link to post Share on other sites
WVHillbilly520H 10,369 #2166 Posted April 21, 2019 Got the Nanco AGs and mushroom iron weights bolted to the 315-8... @The Tool Crib 23x10.50-12 on 7" rims... 4 1 Share this post Link to post Share on other sites
The Tuul Crib 7,332 #2167 Posted April 21, 2019 7 minutes ago, WVHillbilly520H said: Got the Nanco AGs and mushroom iron weights bolted to the 315-8... @The Tool Crib 23x10.50-12 on 7" rims... Ready for anything you can throw at it! Looks great. I’m just waiting another fuel pump and I’m done. The first one I got was leaking and not really sure if it was something I did or if it’s the pump! 1 Share this post Link to post Share on other sites
Herder 2,354 #2168 Posted April 21, 2019 6 hours ago, The Tool Crib said: Slowly getting the parts put back on this little beast of a tractor. I’m ready to start mowing with it any day now! SEAT TIME !!! Looking good!!! We are going to need a video of it running. Share this post Link to post Share on other sites
The Tuul Crib 7,332 #2169 Posted April 22, 2019 On 4/20/2019 at 12:21 PM, ebinmaine said: As we were clearing out trees for the new Horse stable I cut one that leaned over onto others. We used the Cinnamon Horse to drag it a few feet so we could finish cutting. Fantastic torque from the big K341. Note that I had forgotten to raise the engine RPM. That pull was done at IDLE. Imagine how it'll go with a little more appropriate engine spin... Wee wwww weeeee!! 1 Share this post Link to post Share on other sites
The Tuul Crib 7,332 #2170 Posted April 22, 2019 13 minutes ago, Herder said: Looking good!!! We are going to need a video of it running. It sounds as sweet as it looks! 1 Share this post Link to post Share on other sites
Herder 2,354 #2171 Posted April 22, 2019 1 minute ago, The Tool Crib said: It sounds as sweet as it looks! Congrats. 1 Share this post Link to post Share on other sites
Lee1977 6,217 #2172 Posted April 22, 2019 I made a new set of roller axles for my 48" deck. This is the old style like came on the 75-48 MS01. I drilled the 1/2" first then used a roller axle off the free deck to locate the 5/16" mounting hole. I would be done If I could still see to weld. I'll have to get one of my friends to weld the axles in. 2 2 Share this post Link to post Share on other sites
cleat 4,984 #2173 Posted April 23, 2019 I make mine like that as well. Here are mine Here are the plans Deck roller shaft.pdf Yours looks nicer with the rounded off ends. Cleat 5 Share this post Link to post Share on other sites
MIGHTYMO 50 #2174 Posted April 23, 2019 Put the mower deck back on my 314-8 (aka "Moose" as my brother calls it compaired to his troy-bilt rider), mowed the weeds, then gave Moose a bath 3 Share this post Link to post Share on other sites
RetroMower 333 #2175 Posted April 23, 2019 Tried to replace the head gasket on my c100 and didnt 2 bolts snap off. No suprise its the two straddling the exhaust. Suckers are heat treated and hardened and wont drill out. Anyone looking for two great parts tractors? 2 Share this post Link to post Share on other sites
