What have you done to your Wheel Horse today?

[WHX?? 56,234]

9 hours ago, CasaytheMann said:

bottom of the grommet was threaded.

From the motors that just have the plastic threaded in caps for checking oil. On the tube that just sits in the grommet I use a little silicone to seal that area up better. Next time you do an oil change add a 3/8 nipple and elbow to have less messy oil changes. 

Recently parted out one of these machines if you need something let me know. 

 

[cleat 8,949]

1 hour ago, 953 nut said:

         Could the grease be rejuvenated by warming it up with a good old inconstant light bulb for a couple houres?

I doubt that would work.

A little penetrating oil might but taking it apart is best.

[cleat 8,949]

1 hour ago, 953 nut said:

         Could the grease be rejuvenated by warming it up with a good old inconstant light bulb for a couple houres?

I doubt that would work.

A little penetrating oil might but taking it apart is best.

[CasaytheMann 73]

3 hours ago, WHX?? said:

From the motors that just have the plastic threaded in caps for checking oil. On the tube that just sits in the grommet I use a little silicone to seal that area up better. Next time you do an oil change add a 3/8 nipple and elbow to have less messy oil changes. 

Recently parted out one of these machines if you need something let me know. 

 

 Does it have a side discharge or recycler cover? 

Edited 12 hours ago by CasaytheMann

[WHX?? 56,234]

37 minutes ago, CasaytheMann said:

 Does it have a side discharge or recycler cover?

Recycler cover. I don't use them I run a bagger. 

[ML3 2,262]

Got the RJ out of back shed dodging all the mud in yard. Started up & running good. Now if I only can get the recoil fixed for starter. I have 2 1/2 starters but collectively cannot seem to make 1 work! I can rope start it but I want the recoil installed

[WHX?? 56,234]

17 minutes ago, ML3 said:

get the recoil fixed for starter.

What one ML? Did you do a help thread on it?  There are at least three recoils that I know of that is correct for a Clinton 1200/1290. Fairbanks Morse being the most common. Should be easy peasy but they all take different cups. I have manuals on all of them if you need. Engine Clinton Recoil starter ID.pdf

 

 

 

That is a nice looking RJ ... 

Edited 10 hours ago by WHX??

[ML3 2,262]

5 minutes ago, WHX?? said:

What one ML? Did you do a help thread on it?  There are at least three recoils that I know of that is correct for a Clinton 1200/1290. Fairbanks Morse being the most common. Should be easy peasy but they all take different cups. I have manuals on all of them if you need. Engine Clinton Recoil starter ID.pdf

 

 

 

That is a nice looking RJ ... 

Thanks! Once again I can thank @Buckeyes cause I bought it from him. 

I agree, its simple but for some reason I must be simpler.... Appears like the tabs arent moving out to cup. 

 

Thanks for the information.  Ill look at it & hope to figure it out.

 

 

[CasaytheMann 73]

1 hour ago, WHX?? said:

Recycler cover. I don't use them I run a bagger. 

If you have the recycler cover I'd be interested in it. Could you post a picture?

[ineedanother 2,139]

Made quite a bit of progress on the 16 auto hydro swap but I've gotten slow in my old age...hopefully it's by choice 

 

[CasaytheMann 73]

Decided to freshen up the headlight lens and get the headlights operational.