Jump to content

Recommended Posts

scotty

My hitch pin is stuck in my b-80. I was wondering if i were to use my torches where would be the best place to heat it. I was reading someone said not to heat the pin. But if you heated the case wouldnt it end up hurting the transmission split gasket?

Share this post


Link to post
Share on other sites
 
953 nut

Put the torch away and get out the drill! @Ed Kennell did a real good post on the process some time back. He drilled a few holes in the cast iron portion of the transmission that the pin runs through, drilled to the pin, applied several shots of PB Blaster ( or whatever treatment you like best) and then was able to drive the pin out.

  • Like 3

Share this post


Link to post
Share on other sites
 
tunahead72

I'm with Dick (I wonder if this will be censored).  There's several other less drastic things you can try before you get out the torch.  Most involve PB Blaster or some other true penetrating oil (not WD40), patience, time, maybe gentle tapping with a rubber mallet.

 

There's several good threads on this topic here, I'll try to find one of my favorites and get back to you.

--------

The censors have lightened up, nice. :)

Edited by tunahead72
  • Like 4

Share this post


Link to post
Share on other sites
 
tunahead72

I couldn't find the one thread I was really looking for (I think it was lost in one of the software conversions that RedSquare went through a while back), but this one's pretty good:

 

  • Like 1

Share this post


Link to post
Share on other sites
 
scotty

Looks like the first step is to cut the pin off flush and see if it is not just stuck in the hitch itself.

Share this post


Link to post
Share on other sites
 
rjg854

If it as just stuck in the hitch pin itself it would still move up and down.  When I wanted to get one out, I drilled some holes in the hitch pin mount as was already suggested, then after soaking it with PB Blaster for a couple of weeks, I drilled along side of the mount and very near the edge of the pin, until the bit was almost all the way through, then drove it out with a drift pin, and many choice words.

  • Like 1

Share this post


Link to post
Share on other sites
 
scotty

I cut the pin out and got the hitch itself out of the way. It was flush with the case and the pin started to move and eventually i got it out.

  • Like 2

Share this post


Link to post
Share on other sites
 
rjg854

Congratulations, they can be a challenge :handgestures-thumbupright:

  • Like 1

Share this post


Link to post
Share on other sites
 
scotty

Ive got my brinley hitch on already now ive got to rig some sort of lift cable for it

Share this post


Link to post
Share on other sites
 
stevasaurus

I think that is the easiest way.  Use a long pry bar in the slot hitch and get something to give.  Keep going up and down, while putting in some penetrating oil.  Once the hitch moves pretty good, cut it off with a saws-all between the trans and the hitch.  Whatever was moving will now come out...impact air chisel works great.  Now you can take the hitch by itself and drill it out, heat it, press it or do an exorcism.  :)

  • Like 3

Share this post


Link to post
Share on other sites
 
woodchuckfarmer

Used a ball joint press on Riches C-120.

  • Like 1

Share this post


Link to post
Share on other sites
 
608KEB

I used a ball joint press on my B-80. Took a little bit of time. But it came out.

Share this post


Link to post
Share on other sites
 
CasualObserver
On 7/30/2016 at 4:28 PM, 953 nut said:

Put the torch away and get out the drill! @Ed Kennell did a real good post on the process some time back. He drilled a few holes in the cast iron portion of the transmission that the pin runs through, drilled to the pin, applied several shots of PB Blaster ( or whatever treatment you like best) and then was able to drive the pin out.

 

I believe this is the post Dick was referring to.....

 

 

I've also gone back and found a few other old stuck or frozen hitch pin removal topics and added some tags that will help them show up in similar topics.  Check the very bottom of this thread for similar posts. (many of them have links to each other inside them... this is a commonly discussed problem!)

 

 

This is one of the oldest and most referred to....

 

 

 

  • Like 1

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • tractorboy79
      By tractorboy79
      Hello, I have a gt14 and a old brinly cultivator but I need the correct hitch to put on my tractor (clevis hitch) would clevis hitch fit on the back of a gt14 the same way as a another tractor or will I need to make adjustments? Anything helps? thanks!
    • bob54
      By bob54
      How do I get this pin out,  I've tried heat, rust penetrate, and an air hammer, and just rust penetrate and the air hammer.    I can't get it to move, no matter what I do,,and yes I removed the clips from both ends.  I knew you were thinking about that



    • rwilson
      By rwilson
      This might be a dumb question but i'm sure some of you have dealt with this. How do you get the pin out of the rear when it is rusted in there? I just bought a clevis hitch today but i cant get the pin out to put it on.
×
×
  • Create New...