Jump to content
benjiboo

Part # For C-160 Headlight Lense?

Recommended Posts

benjiboo

Can anyone tell me what the part number is for the headlight lense for my C-160? The only things my tractor is missing is that headlight lense and the contacts that go inside the headlight bulb housing where the bulbs drop in. The actual housings for the bulbs are there, but just the wired contacts with the springs are missing, any ideas on replacement contacts for them? Thanks everyone.

Edited by benjiboo

Share this post


Link to post
Share on other sites
 
AMC RULES

The lenses themselves are usually on ebay...

search "wheelhorse lens" and see what happens. 

The light buckets show up there too...

might have to keep checking back though.           :handgestures-thumbsup: 

Don't forget our :wh: parts vendors found in the vendors section here on the forum too. 

Share this post


Link to post
Share on other sites
 
 
gwest_ca

http://www.partstree.com/parts/

 

103771 replaced by 98-1713
ASM - LENS W/DECAL

 

Single wire light socket pigtails can be had from automotive jobbers like Napa.

 

Garry

Share this post


Link to post
Share on other sites
 
MalMac

Yep the socket pigtails can be bought at NAPA. I Just got a box of them this past summer.

Share this post


Link to post
Share on other sites
 
benjiboo

Excellent! I knew you guys could come through. Thanks guys!

Share this post


Link to post
Share on other sites
 
608KEB

Do you think the headlight lens are originals or reproductions with a vinyl sticker on the back side of the Lens?

Share this post


Link to post
Share on other sites
 
546cowboy

I have two brand new ones that I got before I sold all my tractors. As I recall they were about $36 each from my dealer.

Share this post


Link to post
Share on other sites
 
KC9KAS

Yep the socket pigtails can be bought at NAPA. I Just got a box of them this past summer.

Same here...not very expensive either.

Share this post


Link to post
Share on other sites
 
benjiboo

So does anyone have a part # for the socket pigtails from NAPA? I've searched their website over and over and can't find anything even close.

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

  • Similar Content

    • Deer hunter
      By Deer hunter
      Does anyone know where I could find a complete engine rebuild kit from for the k-19 ? I absolutely love my c-195 and have had it for years. But the motor let go last fall and I want to rebuild it or upgrade the motor, any suggestions?
    • BrianStasC-101
      By BrianStasC-101
      Hello all. I am looking for suggestions on adapting the pto from my C series tractor to a harbor freight predator 420 13hp engine. I know the predator motors are a controversial topic however it is the route I have chosen for this particular machine. The intent was to mostly use it for plowing so no PTO required but it would be handy to have. Looking to hear from someone that has successfully done the swap that may offer any advice before I attempt to transfer it over. Just looking for any general pointers that will help me along the way to make it go as smoothly as possible. 
    • HumbleHans
      By HumbleHans
      Operator manual 810343R1
      Wiring
      34 pages 17.5MB
       
      Wiring Colored 
      1 page 228KB
       
      1984 C-105 8-Speed model 11-10K802
      1984 C-125 8-Speed model 11-12K802
      1984 C-145 Automatic model 11-14KE01 - Some used alternate inner axle bearing See PSB #369
      1984 C-165 8-Speed model 11-16K801
      1984 C-175 Twin Automatic model 11-17KE01 - Some used alternate inner axle bearing See PSB #369
      1984 C-195 Twin Automatic model 01-19KE02
       
       
    • t_furl43
      By t_furl43
      1979 c-101 nice project tractor just needs a few odds and ends, steering wheel, coil, carburetor bowl, the wiring was redone by previous owner....all 4 tires are good and hold air it goes into all gears no problem, transmission fluid has been changed, 10hp Kohler, message me or call or txt with any questions, it does run and runs well,  it’s been kept inside since I’ve had it, I would also trade for a mid mount grader blade thanks 




      92DB561C-FF95-4868-A52B-5725D4D3B9DE.mp4
    • RJ Hamner
      By RJ Hamner
      Will the plow I am using on my C121 and C160 work on a 876?  
      or is the plow frame different?
      Thanks
      Bob
×
×
  • Create New...