Jump to content
Sign in to follow this  
amard58

C-175 Plow rod for down pressure

Recommended Posts

amard58

I understand there is a way to get down pressure on my blade by replacing the chain link with a straight 'piece'. Is there a part number for this piece or is it something that gets fabricated?

Does anyone have what I need and willing to sell, or can someone provide a photo of the part with the dimensions so I can get one fabricated?

Thanks in advance.

Share this post


Link to post
Share on other sites
 
can whlvr

if noone has a pic handy i will try and get one tommrow,its a flat bar,at least 5/16 thick,about 1 inch wide,and about 12 inches long with a pin at each end,one to go to the bell crank and the other to the blade,its very simple and can be made with a bar and some bolts,i think the space between the pins is 11 1/2 inches

Share this post


Link to post
Share on other sites
 
Hodge71

:text-yeahthat:

Share this post


Link to post
Share on other sites
 
SgtBob

Here are a couple photos of what you need. 1/4 " thick, 12 1/2" overall length, 1 1/4" inch wide, with a pin at each end ( pins are 11 1/2 " apart center to center). Please let me know if you have any other questions.

DSCF0187-1.jpg

DSCF0186.jpg

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

  • Similar Content

    • Deer hunter
      By Deer hunter
      Does anyone know where I could find a complete engine rebuild kit from for the k-19 ? I absolutely love my c-195 and have had it for years. But the motor let go last fall and I want to rebuild it or upgrade the motor, any suggestions?
    • BrianStasC-101
      By BrianStasC-101
      Hello all. I am looking for suggestions on adapting the pto from my C series tractor to a harbor freight predator 420 13hp engine. I know the predator motors are a controversial topic however it is the route I have chosen for this particular machine. The intent was to mostly use it for plowing so no PTO required but it would be handy to have. Looking to hear from someone that has successfully done the swap that may offer any advice before I attempt to transfer it over. Just looking for any general pointers that will help me along the way to make it go as smoothly as possible. 
    • HumbleHans
      By HumbleHans
      Operator manual 810343R1
      Wiring
      34 pages 17.5MB
       
      Wiring Colored 
      1 page 228KB
       
      1984 C-105 8-Speed model 11-10K802
      1984 C-125 8-Speed model 11-12K802
      1984 C-145 Automatic model 11-14KE01 - Some used alternate inner axle bearing See PSB #369
      1984 C-165 8-Speed model 11-16K801
      1984 C-175 Twin Automatic model 11-17KE01 - Some used alternate inner axle bearing See PSB #369
      1984 C-195 Twin Automatic model 01-19KE02
       
       
    • t_furl43
      By t_furl43
      1979 c-101 nice project tractor just needs a few odds and ends, steering wheel, coil, carburetor bowl, the wiring was redone by previous owner....all 4 tires are good and hold air it goes into all gears no problem, transmission fluid has been changed, 10hp Kohler, message me or call or txt with any questions, it does run and runs well,  it’s been kept inside since I’ve had it, I would also trade for a mid mount grader blade thanks 




      92DB561C-FF95-4868-A52B-5725D4D3B9DE.mp4
    • RJ Hamner
      By RJ Hamner
      Will the plow I am using on my C121 and C160 work on a 876?  
      or is the plow frame different?
      Thanks
      Bob
×
×
  • Create New...