Silas Sealscott 3 #1 Posted 23 hours ago I have a 1970 wheelhorse electro 12 it has a 12ph k301 Kohler with the rare breakless magneto ignition system and I converted it over to point ignition from another later 12hp kohler and I don't know what ignition switch to get or if I can just use the old one and I don't have a wireing diagram and someone who had it before me put a starter solenoid on it. so if anyone has had the same problem or knows how to wire it up with the point ignition I would much appreciate it if you would help me so I can get this wheelhorse backup and running. Share this post Link to post Share on other sites
pfrederi 21,312 #2 Posted 23 hours ago You will need to change to change the ignition switch. Since yo have a solenoid for the starter a regular 5 terminal Battery Points switch will work. 103990 make sure it has an"I" terminal not an "M" 3 Share this post Link to post Share on other sites
Silas Sealscott 3 #3 Posted 22 hours ago 16 minutes ago, pfrederi said: You will need to change to change the ignition switch. Since yo have a solenoid for the starter a regular 5 terminal Battery Points switch will work. 103990 make sure it has an"I" terminal not an "M" do you know how I would go about wiring it Share this post Link to post Share on other sites
Ed Kennell 47,827 #5 Posted 22 hours ago This may help.1970 electro 12 key switch - Wheel Horse Electrical - RedSquare Wheel Horse Forum 1 1 Share this post Link to post Share on other sites
pfrederi 21,312 #6 Posted 22 hours ago Run a wire from the "I" terminal of the ignition switch to the small + terminal on the coil 1 Share this post Link to post Share on other sites
Silas Sealscott 3 #7 Posted 22 hours ago 10 minutes ago, Ed Kennell said: This may help.1970 electro 12 key switch - Wheel Horse Electrical - RedSquare Wheel Horse Forum ok thanks but I don't know if it is the same because I converted the breakless ignition to point ignition. 1 Share this post Link to post Share on other sites
gwest_ca-(File Mod) 12,535 #8 Posted 21 hours ago Since it has a solenoid added the ignition switch you have may be this one. They all look alike but the differences are the terminal locations and how they are labeled. Original switch - heavy duty - click on the picture in each link to see more without downloading files Magneto ignition light duty - if it is different can you post a picture of the back of it? Battery ignition and very common Share this post Link to post Share on other sites
Silas Sealscott 3 #9 Posted 21 hours ago 36 minutes ago, gwest_ca said: Since it has a solenoid added the ignition switch you have may be this one. They all look alike but the differences are the terminal locations and how they are labeled. Original switch - heavy duty - click on the picture in each link to see more without downloading files Magneto ignition light duty - if it is different can you post a picture of the back of it? Battery ignition and very common I know what switch I need but I don't know how to wire it up because I converted the k301 with breakless ignition to point ignition if some one has a digram on how wire the tractor up after converting it it would help me out Share this post Link to post Share on other sites
Silas Sealscott 3 #10 Posted 21 hours ago 1 hour ago, pfrederi said: Run a wire from the "I" terminal of the ignition switch to the small + terminal on the coil can I use this switch Share this post Link to post Share on other sites
gwest_ca-(File Mod) 12,535 #11 Posted 21 hours ago Yes that is a good one to use. 5 minutes ago, Silas Sealscott said: can I use this switch 2 Share this post Link to post Share on other sites
gwest_ca-(File Mod) 12,535 #12 Posted 21 hours ago If you can identify the wires on your present switch it is easy to change them to the correct terminals on the 103990. Using the plastic 5-wire connector body makes it fool proof in the future. Share this post Link to post Share on other sites
953 nut 70,374 #13 Posted 14 hours ago Here is a drawing that can be used to wire the tractor since there are no safety switches. It uses the 103990 ignition switch. If you are using the electric PTO you can run a second fused wire from the "A" terminal to the PTO. Wire colors are up to you. 1 1 Share this post Link to post Share on other sites
Silas Sealscott 3 #14 Posted 1 hour ago 12 hours ago, 953 nut said: Here is a drawing that can be used to wire the tractor since there are no safety switches. It uses the 103990 ignition switch. If you are using the electric PTO you can run a second fused wire from the "A" terminal to the PTO. Wire colors are up to you. thanks you this was what I was looking for 2 Share this post Link to post Share on other sites