FLtractor 253 #1 Posted Monday at 07:26 PM Afternoon, I have attempted to step on pedal near pulley.. use clutch .. slip belt off by hand.. no luck. What is the best way to removal this belt and then replace ? Share this post Link to post Share on other sites
ri702bill 13,323 #2 Posted Monday at 07:46 PM Remove the idler pulley and its bent tab bracket. That should give you the slack needed to peel it of one of the pulleys - works on my 702 & 854... 1 Share this post Link to post Share on other sites
peter lena 10,115 #3 Posted Monday at 09:50 PM @FLtractor that belt fraying , reflects back on related , bearings , noisy / dry rough , incremental bearing stoppage , leads to belt bounce , fraying , everything looks bone dry . ever lubricate related linkage ? pete Share this post Link to post Share on other sites
FLtractor 253 #4 Posted Monday at 10:36 PM 2 hours ago, ri702bill said: Remove the idler pulley and its bent tab bracket. That should give you the slack needed to peel it of one of the pulleys - works on my 702 & 854... Thanks. Will give it a go Share this post Link to post Share on other sites
FLtractor 253 #5 Posted Monday at 10:37 PM 45 minutes ago, peter lena said: @FLtractor that belt fraying , reflects back on related , bearings , noisy / dry rough , incremental bearing stoppage , leads to belt bounce , fraying , everything looks bone dry . ever lubricate related linkage ? pete Have not lubricated since owned no.. Going to replace belt with new proper ribbed belt once I find out which model # I need from local NAPA. 1 Share this post Link to post Share on other sites
FLtractor 253 #6 Posted 1 hour ago (edited) On 11/16/2026 at 2:46 PM, ri702bill said: Remove the idler pulley and its bent tab bracket. That should give you the slack needed to peel it of one of the pulleys - works on my 702 & 854... I removed the center pulley and still can’t pull the belt off either of the 2 remaining pulleys Edited 1 hour ago by FLtractor Share this post Link to post Share on other sites
ri702bill 13,323 #7 Posted 37 minutes ago (edited) OK - it sounds like the belt MAY be the wrong size and a bit (1") too short, but yet it looks about right for length & width... What is the P/N on the belt? That IS an Early Tach-a-Matic implement mount, right, whereto deck drops out the bottom of the slot on both plates?? Very early ones did not - you had to remove the RH mount from the tractor & lift up to get the belt off. No slot - A real PITA. Edited 32 minutes ago by ri702bill Share this post Link to post Share on other sites
FLtractor 253 #8 Posted 22 minutes ago 12 minutes ago, ri702bill said: OK - it sounds like the belt MAY be the wrong size and a bit (1") too short, but yet it looks about right for length & width... What is the P/N on the belt? That IS an Early Tach-a-Matic implement mount, right, whereto deck drops out the bottom of the slot on both plates?? Very early ones did not - you had to remove the RH mount from the tractor & lift up to get the belt off. No slot - A real PITA. Since belt should be replaced anyway… Thinking of cutting the belt in half to get off pulley … I can then measure it.. should be 1/2 by 28 inches if not mistaken. not sure what to look for to tell if it’s tach o matic with the bottom slot. Share this post Link to post Share on other sites
ri702bill 13,323 #9 Posted 9 minutes ago Look at the inverted slots on each of the side plates to locate the front cross shaft... That is the later style. Mower Rotary 36in RD 1966 RM-366 _A-5252[1].pdf Share this post Link to post Share on other sites