Fuel Line Fittings

[702854boy 483]

Would anyone happen to know where I could get some fuel line fittings like the ones in the photo? Also would I need anything special like a specific type of line or flare putter onner?

[ri702bill 11,224]

Are you looking for all three pieces - the threaded fitting, the nut, and the soft sealing cylindrical part??

If you are looking for just the sealing parts, I have bought them in the past from Lowell.

[WHX?? 54,830]

Ebay & reform the line. Nothing else needed.

Keep few for extras & make some friends here. 

Edited 16 hours ago by WHX??

[rmaynard 16,847]

I've got some. How many do you need? 

Text me 443-398-6544

[702854boy 483]

1 hour ago, ri702bill said:

Are you looking for all three pieces - the threaded fitting, the nut, and the soft sealing cylindrical part??

If you are looking for just the sealing parts, I have bought them in the past from Lowell.

The fitting and nut seem to be in good condition but the seals appear to be pretty cracked and the one fitting is able to slip off the end of the line so I wasn't sure what was needed to flare and reseal.

[WHX?? 54,830]

Go text Bob he's like me he's gotta buy some friends too. 

Lowell you gotta pay to be his friend. He's prolly got just the rubbers too. 

https://wheelhorsepartsandmore.com/product/brass-fuel-fittings-qty-2/

 

[sqrlgtr 2,129]

Parker 3/16" Compression Viton Sleeve 10PK 60VLV-3 | Zoro

These used to be half the price they are now.

[WHX?? 54,830]

That's not terrible for 10 Squirrelly. Bet they want another 30 for shipping tho. 

Best check with Handy Don & RI Bill to make sure viton is compatible with rocket fuel tho.  You know how they like to make lunar rovers out of GTs ...  just kidding guys sense of humor check just kidding ... 

Edited 13 hours ago by WHX??

[oliver2-44 11,211]

I spare Handy Don and RI Bill.
Yes, Viton is comparable with gas, oil, grease. It is an upgrade from conventional rubber. 

[sqrlgtr 2,129]

41 minutes ago, WHX?? said:

That's not terrible for 10 Squirrelly. Bet they want another 30 for shipping tho. 

$5.00 shipping is what it shows in my shopping cart.

Edited 12 hours ago by sqrlgtr

[Racinbob 12,739]

I use a cheap tubing bender and hardware store compression fittings. 

 

[ri702bill 11,224]

4 minutes ago, Racinbob said:

and hardware store compression fittings.

The only possible issue I see happening is fatigue cracking from vibration using these. Perhaps that is the reason for the soft seal??

FYI - the ones I bought appear to be made of 3/16 (5mm) automotive fuel injection hose....

[Racinbob 12,739]

10 minutes ago, ri702bill said:

The only possible issue I see happening is fatigue cracking from vibration using these. Perhaps that is the reason for the soft seal??

FYI - the ones I bought appear to be made of 3/16 (5mm) automotive fuel injection hose....

 

Because the pump and carb are both solidly mounted to the engine I don't think that would be a problem. Being compression fittings there's no rubber seal for the fuel to attack. I did that shortly after I got the tractor at the 2018 show and it's been fine. That 854 is dedicated to the sickle mower so a breakdown is nothing more than a nuisance but I'd likely still go electric if there was an issue.

[Retired Wrencher 6,420]

14 hours ago, 702854boy said:

Would anyone happen to know where I could get some fuel line fittings like the ones in the photo? Also would I need anything special like a specific type of line or flare putter onner?

I have a few for the bigger engines eight and up. They’re a little dirty, but they could be cleaned out. Let me know if you want them. I’ll just send them to you. You’re also gonna need the little rubber grommets on the end. I believe I have the part number for that.