What's this clamp called? I need to order some.

[ebinmaine 73,576]

This goes under the feets steps on a C series or newer.  

 

[squonk 44,088]

Clamp

[stevasaurus 23,353]

ACE or any hardware store has them.  Used to hold cable, wire, tubing in place.  You could probably get what you need off any telephone pole.    With all of the granite in Maine, they may be in your back yard on any pole.  

[ebinmaine 73,576]

7 minutes ago, squonk said:

Clamp

 

Good job Mike. 

 

[squonk 44,088]

I looked up my c-160 parts diagram on Jacks. Of course they don't show the clamp. 

[ebinmaine 73,576]

2 minutes ago, squonk said:

I looked up my c-160 parts diagram on Jacks. Of course they don't show the clamp. 

 

I appreciate the effort though! 

[wallfish 18,413]

You can find them in the electrical section for conduit clamps

[squonk 44,088]

#7456 Bracket.  I'm sure A-Z has a pail full

[Blue Chips 65]

You might have a look at this site: https://kugelkomponents.com/product-category/line-clamps/single-line-clamps/

 

I don't know if they sell individual ones. Prices are for a multi-pack. Note: These are stainless steel clamps.

 

For my tractors, Toro just calls it a 'foot rest bracket.'

 

Edited Sunday at 09:42 PM by Blue Chips
Added detail.

[gwest_ca-(File Mod) 11,577]

EMT tubing has odd diameters. 1/2" is .706" OD and 3/4" is .922" OD and the clamps fit accordingly.

I'll guess the one you want is for 3/4" round bar. The 1/2" clamp should work. Commonly called a one hole strap.

[953 nut 60,877]

1/2" Ridged electrical conduit has an outside diameter slightly over 3/4" and the clamps are made of heavier material. A bag of 5 cost less than $ 2.00 at the big box stores.

https://www.lowes.com/pd/Sigma-Electric-ProConnex-1-2-in-One-hole-Strap-Intermediate-Metal-Conduit-Compatible-Galvanized-Rigid-Conduit-Compatible-Rigid-Metal-Conduit-Compatible-Conduit-Fitting/1000152549?store=717&cm_mmc=shp-_-c-_-prd-_-elc-_-ggl-_-CRP_SHP_LIA_ELC_Online_Mid_Priority(E+Band)_Omni-_-1000152549-_-local-_-0-_-0&gclsrc=aw.ds&gad_source=1&gad_campaignid=22867870040&gbraid=0AAAAAD2B2W97pEK6Dx69ZOiriDUVQ8XeP&gclid=CjwKCAjwz5nGBhBBEiwA-W6XRHKXVhha5lgVGfw3jClJatCIXIxjmkH4cqZBgmPIXmtiLxdzr92_mRoCOOMQAvD_BwE

[c-series don 10,253]

@ebinmaine if you are looking for the factory correct ones I think I have some I can send you. Text me if you want them. 

[oldlineman 1,567]

953 nailed it we called them oneyed pipe straps for rigid pipe or conduit

[1968Commando 167]

7 hours ago, ebinmaine said:

This goes under the feets steps on a C series or newer.  

 

Conduit clamp 

[Racinbob 12,017]

Halex 1/2 in. Rigid 1-Hole Strap (4-Pack) 96111 - The Home Depot

 

A little fine tuning will be needed. Get the ones for rigid pipe. The big box straps for EMT are lighter. These days I've noticed that even the rigid straps are sometimes lighter.

 

Edited 23 hours ago by Racinbob

[gwest_ca-(File Mod) 11,577]

1/2" rigid conduit has an OD of .840"

3/8" rigid conduit has an OD of .675" - Did not know there was such a thing