Leaderboard

The time has come for me to part with my trusty Wheel Horse and find it a new home. I am the second owner (since 2003) and it has always been stored in a garage. I am located about 20 minutes south of Rt 80 or 15 minutes north of Rt 78 near Rt 33 for those who are attending the Big Show. 1975 C-120 Special, 8-speed (Model 1-0375, Ser. # 133357). Running (no smoke) 12 hp Tecumseh (Model HH120-120180E, rebuilt 1986). Rebuilt carb, new fuel pump, and new ignition module (in 2006). Good used replacement tank, original tank is included in the sale. Brand-new battery, fuel filter, and shutoff valve installed 5/26. The transaxle case is cracked near the center flange and repaired with JB Weld. Solid 42” side discharge deck (Model 5-1010) bearings replaced in 2005. Extra set of Gator mulching blades and spare hi-lift blades included. 42” snow/dozer blade (Model 86-42bc010), with Rear weights, tire chains and hardware. Parts: 4 NOS belts and 2 good used belts, NOS taillight lenses, used starter, used ignition module, more (see pic). 1975 C Series Owner’s manual, 1975 WH accessory catalog, 5-1010 deck manual, original HH-120 manual, updated Tecumseh HH-120 technicians handbook. Selling entire package for $350 Or Best Offer Deck/Blade/Weights/Parts alone are worth that! Please PM to contact HH120_running.mp4

I decided not to retire yet so I’m still rebuilding I have Single cylinder Kohler K and Magnum series engines for sale k240, k301, k321, k341, M10, M12, M14 and M16. Long blocks starting at 800.00 depending on model and application. All engines are torn down to the bare block. If I don’t have your specific engine in stock let me know. I don’t cut corners with my rebuilds. All work is done to professional standards. I no longer stock or rebuild twin cylinders. I no longer stock or rebuild k91, k161 and k181 engines. Contact me via PM with any questions. Located in Mechanicsville, VA.

Hello all, I put my 520-8 up for sale on page 13 of the big show sale thread. Figured id add it here too to catch those not looking over there. Late to party, last minute for sale... 520-8 with good 42" s/d deck (blades nfg) Unit has 875 hours and clock works. All idiot lights and gauges work. Fresh oil and good battery. Yes it does need some light bulbs and minor doo dads. But it is still solid and very strong Tractor was used but not abused and runs great with no smoke or bad noises. Charging system works. I had plans to tear it apart and do a resto mod / rebuild it the way I would build a "520" and have come to realise I have enough 500 series parts laying around to build one using a 300/400 series as a starting platform. $1500 is my number... with genuine Wheel Horse wheel weights bring $500+ I feel this piece of Wheel Horse lore is worth it. I will haul to big show if paid in advance. Thanks Tony Andover CT (860)978-9039

Work Horse GT-1142 for sale. Stored indoors, not original paint, w/ 42” rear discharge deck. The deck has had some repairs but is operational. Needs a battery. Motor has an oil leak which led me to park it. I last ran this tractor about 5 years ago and have not touched it since but has since been stored indoors and I had intentions to restore it someday. It has been in my family and passed down since it was bought new. I’d like to free up space now. I’m located in Mineral Springs, PA just off interstate 80 and tractor/deck would have to be picked up. If interested in further details or images please send an email and we’ll go from there. Thanks

Landscaping changes made this working tractor an inefficient way to cut our lawn. Original owner had removed most WH side badging and added Ferarri stickers. Fired it up yesterday and it drove and mowed. Includes the snow thrower attachment, not pictured, which I have not attempted to install, so belt need replacement and possible missing parts may be issues if you want to chuck snow with it. Please pick up here in Aurora, IL or arrange your own transport. Might deliver locally if it makes sense. Reasonable offers entertained. Thanks to the forum members who helped me get this beastie running again!

I have too many projects, so here is an 875 roller. The PO added a hydro lift to the original Wheelamatic. The lift and the hydro drive work...however I am not sure putting a hydro lift on was a good idea, lifts were not an option on Wheelamatics. . I can't figure out where there would be an implement relief valve. The hose to the front of the cylinder leaks badly but the cylinder itself and control valve seem good. There is a hood but it was cut to clear a B&S engine. Steering is very sloppy and motion control needs work one rear tubeless tire goes soft. The engine is NOT included, put it on to test the hydro. I can't bring it to the show (not enough room in my truck and I can't pack like pullstart😀). However, if you live in the Northeast and are going to/from the show, I am 3 miles off I-81 (exit 211) north of Scranton

Up for sale is a 1973 Wheel Horse 18 Auto. Older restoration, tractor runs good has a new fuel pump both rear tires are tubed. Price is obo, if you have any questions feel free to ask. Can be brought to the big show, thanks for looking

Infamous Toro Wheel Horse 520-8 with clean 60" deck and electric attachment / implement lift. Supposidely 1 of 225 made . This one was tore down, restored and painted. Engine was fully rebuilt with Onan parts. Transaxle was resealed / got new bearings where needed. I bought it to add to my collection but have decided to take the $$$ and invest in a different project. Tractor is in my garage in South Windsor CT 20260619_112009.mp4

Barn find and looking good some minor rust spots seen on pictures. I have the top belt guard from the mower deck that’s not seen in the pictures. Oh and I added the fuel filter that’s not original. Please ask any questions. Thanks for looking.

I needed a few items from this tractor and now passing it along to keep another alive. The hydrostatic rearend is still good and any other supporting parts. I removed the sheet metal and tires for my project. I can load onto your truck or trailer! DID I SAY FREE?? Lol

Queen size raised air mattress. Has built in 115 volt air pump. For inflation/deflation. Air valve leaks a small amount but will stay inflated overnight. Only used a couple times for camping in a enclosed. Pickup only or can deliver to the Big Show 2026.

For sale front wheel weights for a 520. Can bring to the show if paid in advance. Thanks

Looking for a 520H I love the Onan engine. I'm in Southern Kentucky. Thank you very much.

Wheel Horse D200 Tractor w/mowers. Engine strong and does not smoke. New plugs and fuel pump. The hydraulic pump seal however has started leaking so I took it out of action. Still runs and drives but needs fixing. New Sundstrand 15-Series seal is $48. Has rear wheel weights not shown. Rear 3-pt hitch works along with attachments. 48" rotary pto mower and 44" belly mower deck included.

# 108309 Engine Mounts – Isolation for Wheel Horse I bought these solid isolation engine mounts for my C-141 at a barn sale, but I sold the tractor today and no longer need them. Free shipping to lower 48 states - $30 Venmo or PayPal

I have a front cutter bar for sale. Will bring to the show if paid for prior. Very good shape and works as it should.

Original 1978 C-121. 42 in side discharge is close to new. Have brand new mule drive. Includes factory wheel weights, cigarette lighter, snow blade. All it needs is an owner. Thank you for looking

Rear kit for 3/4/500 series. I do not have the conduit for it but may be obtained from other sources or fabricated. Free shipping.

RJ Suburban repop Showerhead muffler 3/4 formed steel not printed. $175 ea. shipped

1993 Wheel Horse 520 – H with 580 hours . This tractor has been well cared for as pictures speak for itself. This is a turnkey machine with no leaks or issues. It has a brand new 2 inch receiver hitch that is included in the sale. $3250 Located in Southington Connecticut Can be shipped anywhere 📞 860_681_3610

Parting out my C120. This deck was on it. It's in great shape. Needs belt. No rust through. Spindles feel good. Fresh sharpen and balance on blades.