Leaderboard

312-8 and c-160 good parts

1474 hours. Needs rewired, will not start with key and wires are burned. Fresh service when I received it. 60 inch deck, snowblower and tire chains. I do have all the books, sales receipts, complete history. Does run and mow excellent. Have all hubcaps and a box of belts, filters and misc pieces. Lost all interest

What we have here is a 0736TL04 tiller and fitments needed to mount on many long frame, C series, 300/400/500 series tractors. Notable details: Gearbox and tines have low hours. Tarp had blown off mid-mount idlers and got rusted up, probably need penetrating oil and new idlers. Axle mount is rusty/restorable/useable. Lift cable has nylon worn through on one side (they tend to do that). One rear jackshaft bushing has couple ears broke off, and jackshaft e-clips are lost. Belt is original. See picture, ask questions, more pictures available. Pick up in my back yard near Elida, Ohio. Bring help to load, or ramps or something. I think it may be worth $100. - or - Would consider trade for a used car or truck hood that I can use for a sled to drag firewood and equipment around on, something kinda rounded without points or ridges to catch. Have been using an S-10 hood for years, and it's wearing through becoming less useable. What 'cha got?

Very nice Wheel Horse embossed mid back tractor seat. No rips, holes, tears. Binding not loose anywhere. $125 plus shipping. PENDING!

I have 1974 B-80, 1975 B-80, 1978 B-81 / B-111, 300 & 400 Series Manual, & operating instructions for Dozer/Snow Blade 42" & 48" blades. I want to sell all for $25 o.b.o.

I have three old decks 37", 2-42" with spindles, blades, wheels, idlers, etc., a C141 with 14HP Kohler that needs rebuild, no deck. Also a Workhorse with 11HP Kohler engine with carb issues, no deck. Good rubber on both. Also have rear wheel weights. Both tractors need work, seats, fuel lines. Looking to sell as a lot but willing to deal. Local delivery may be possible. Just have too many projects now and need space. Asking $700. I'm in Ledyard CT near New London.

Mid mount grader blade very good condition. Swap for Uni Drive 8 speed transmission with 1 1/8" axles

I have too many projects, so here is an 875 roller. The PO added a hydro lift to the original Wheelamatic. The lift and the hydro drive work...however I am not sure putting a hydro lift on was a good idea, lifts were not an option on Wheelamatics. . I can't figure out where there would be an implement relief valve. The hose to the front of the cylinder leaks badly but the cylinder itself and control valve seem good. There is a hood but it was cut to clear a B&S engine. Steering is very sloppy and motion control needs work one rear tubeless tire goes soft. The engine is NOT included, put it on to test the hydro. I can't bring it to the show (not enough room in my truck and I can't pack like pullstart😀). However, if you live in the Northeast and are going to/from the show, I am 3 miles off I-81 (exit 211) north of Scranton

K321 wheel horse spec long block plus the pan, head valve breather assembly. This engine has been torn down to the bare block cleaned and Bored .010 over, crank ground .010, valve seats ground, head decked. New piston, rings, rod, valves, guides, seals and gaskets. Located in Mechanicsville, VA. 800.00 no core required. Complete K321 drop in ready wheel horse spec k321. This engine has been torn down to the bare block cleaned and Bored .010 over, crank ground .010, valve seats ground, head decked, new carburetor, new piston, rings, rod, valves, guides, seals and gaskets, air filter, plug, fuel pump, points and condenser. Add oil and it’s ready to go. 975.00 no core required.

42" SNOW PLOW & FRAME (2) NO REAR MOUNTING BRAKET / HARDWARE, ALSO MISSING BLADE ANGLE ADJUSTMENT HANDLES NOTE: The “A” style is for short frame mid-to-late 60’s tractors, mounts ahead of the axle housing. The parallel frame is for long frame tractors from the 70’s onward, mounts under the rear axle PRICE LISTED IS FOR EVERYTHING, NOT EACH

This is a project. No electrical hooked up, no fuel lines hooked up. Kohler 10hp replacing the original engine. I got it this way and had plans on completing it and realize I won't be. Also extra set of rear rims. Someone save it please.