Jump to content
The Tuul Crib

Torington B-1416 needle bearing

Recommended Posts

The Tuul Crib

Started to put my sunsrtand together and 

ran into an ef up with the needle bearing .

l have looked for a wheelhorse number 

for the b-1416 and want to make sure l 

get the correct one. Any help on the part number would help. Thanx!

Share this post


Link to post
Share on other sites
 
pfrederi

Is that a bearing in the hydro gear motor???

Share this post


Link to post
Share on other sites
 
The Tuul Crib

Yes there are four of them . 
 

Share this post


Link to post
Share on other sites
 
pfrederi

Do not think you will find WH numbers.  Hydro gears were repair by replacement.  I was curious as to why you took yours apart. Were you able to fix anything??  Pumps you can do something to but not sure what you can do to a gear motor.  Aldon took one apart once to change the output gear to work with a GT14

Share this post


Link to post
Share on other sites
 
The Tuul Crib

Took it apart to resurface the slippers 

the swash plate and surfaces in need 

of repair.  I guess the word would be 

complete.

Share this post


Link to post
Share on other sites
 
gt14rider

Torington b- 1416 is still available,  I replaced 2 on out put shaft, (buggerd up 1 taking shaft out. ) snap rings are available at( LJ power ). 

Screenshot_20190323-134037_Gallery.jpg

Share this post


Link to post
Share on other sites
 
The Tuul Crib
12 minutes ago, gt14rider said:

Torington b- 1416 is still available,  I replaced 2 on out put shaft, (buggerd up 1 taking shaft out. ) snap rings are available at( LJ power ). 

Screenshot_20190323-134037_Gallery.jpg

Does lJ fluid power have these needle bearings? I did the same thing on my bearing that's why I have to get another one. And I also realized there is an O-ring inside the part with the four bolt holes.

Share this post


Link to post
Share on other sites
 
gt14rider

I purchased bearings from bearing distributors troy ny. But I'm sure any good bearing supply Co should be able to get them. Check out the vendors on here. Check out my post ( gt14 90-2062 ) it has o ring #s , different tid bits I've learned so far , 

20190406_171630.jpg

20190406_172014.jpg

20190409_135046.jpg

Share this post


Link to post
Share on other sites
 
The Tuul Crib
11 minutes ago, gt14rider said:

I purchased bearings from bearing distributors troy ny. But I'm sure any good bearing supply Co should be able to get them. Check out the vendors on here. Check out my post ( gt14 90-2062 ) it has o ring #s , different tid bits I've learned so far , 

20190406_171630.jpg

20190406_172014.jpg

20190409_135046.jpg

I have already received the gasket set and seals plus O-rings from LJ fluid power. Just went to eBay and found two needle bearings in case I mess another one up. 
i'll check it out! Thanx!

Share this post


Link to post
Share on other sites
 
The Tuul Crib
On 8/2/2020 at 4:05 PM, gt14rider said:

I purchased bearings from bearing distributors troy ny. But I'm sure any good bearing supply Co should be able to get them. Check out the vendors on here. Check out my post ( gt14 90-2062 ) it has o ring #s , different tid bits I've learned so far , 

20190406_171630.jpg

20190406_172014.jpg

20190409_135046.jpg

Do you remember what you torqued

these ten bolts to. I can't seem to find a chart anywhere for the specs?

Share this post


Link to post
Share on other sites
 
gt14rider

I use bolt torque chart for bolts with out torque spec 

Screenshot_20200809-104119_Chrome.jpg

Share this post


Link to post
Share on other sites
 
The Tuul Crib
1 hour ago, gt14rider said:

I use bolt torque chart for bolts with out torque spec 

Screenshot_20200809-104119_Chrome.jpg

Great thanks for that. Now my next problem is I torqued the bolts down on that piece and I cannot turn the gear after l torque them.Cannot figure out why this is happening. When I loosen them back up I can turn it fine.

Share this post


Link to post
Share on other sites
 
gt14rider

Did you set the bearing deep enough as to not bind on snap ring or gear, or the 4 bolts on gear side collar, turn that collar, see if that binds. 

20190316_163027.jpg

Screenshot_20190323-134037_Gallery.jpg

20190406_171732.jpg

Share this post


Link to post
Share on other sites
 
The Tuul Crib
7 minutes ago, gt14rider said:

Did you set the bearing deep enough as to not bind on snap ring or gear, or the 4 bolts on gear side collar, turn that collar, see if that binds. 

20190316_163027.jpg

Screenshot_20190323-134037_Gallery.jpg

20190406_171732.jpg

Yes I took it back apart again and check those clearances and there's plenty of room. That gear turns really hard and I don't believe that it should turn that hard once it's all together. I check the torque specs on the bolts the eight bigger ones or the 3/8 ones are torqued at 23 and the two smaller the 5/16 are torqued at 8 foot pounds

Share this post


Link to post
Share on other sites
 
Stormin

I wonder if a needle in a bearing has been dislodged? 

Share this post


Link to post
Share on other sites
 
The Tuul Crib

All the needle bearings look in tact.

 

Share this post


Link to post
Share on other sites
 
gt14rider

Any progress :confusion-scratchheadblue:

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...