ebinmaine 79,896 #26601 Posted yesterday at 12:00 AM 2 hours ago, Sparky said: Wish I was going to Jim’s in September… Trina says you need to deliver that transmission up here. We'll take you out on our forest trails. Rough. Terrain. Mebbe hike across the street. I'm willing to supply coffee. 2 Share this post Link to post Share on other sites
kpinnc 18,796 #26602 Posted yesterday at 04:13 AM 4 hours ago, 953 nut said: What the heck, no hydros? I go 4 of those too. 2 Sundstrand and 2 Eatons. 1 2 Share this post Link to post Share on other sites
Ed Kennell 46,722 #26603 Posted yesterday at 02:02 PM Did some maintenance on the 42" SD that I replaced with the 48" SD. New blades New idler pulley Scraped and wire brushed Oil soak then store till next spring 6 4 Share this post Link to post Share on other sites
ML3 2,438 #26604 Posted 23 hours ago Got the Bervac swapped onto 416. Also swapped rear hitch, larger wheels/tires from Workhorse. Still have a few more preventive maint items to get done. Got lift assist springs installed/adjusted & 150lbs of weight on hitch. Now I gotta figure out what to do with the Workhorse. Be nice to have it for parts but dont really want it sitting around...... 20260814_133023.mp4 2 6 Share this post Link to post Share on other sites
Ed Kennell 46,722 #26605 Posted 23 hours ago 5 minutes ago, ML3 said: Got the Bervac swapped onto 416. Looks good...now for a blizzard and a video! 2 Share this post Link to post Share on other sites
c-series don 12,231 #26606 Posted 22 hours ago 1 hour ago, Ed Kennell said: Looks good...now for a blizzard and a video! Ok Ed, you asked for it! 🤣 IMG_4058.mov 1 2 1 Share this post Link to post Share on other sites
sqrlgtr 3,500 #26607 Posted 20 hours ago (edited) Installed front wheel weights on my 312-8 Edited 20 hours ago by sqrlgtr 5 Share this post Link to post Share on other sites
ineedanother 2,678 #26608 Posted 18 hours ago Did a diesel fuel flush and gear oil change on the 161 before installing the ARK for the first time. Lessons learned...black hoods are too wide to clear the hydraulic pump and a shaker plate calls for an inch or so shorter belt It's always something. 2 6 Share this post Link to post Share on other sites
MainelyWheelhorse 2,971 #26609 Posted 18 hours ago Mowed the Fire Station and my lawn. Halfway through my lawn I broke a deck belt. Fortunately when the deck belt broke on the 312 it was at my house and not at the Fire Station. The 308 finished up the lawn, but that is needing attention as it REALLY doesn’t like running the PTO under load. It’s to the extent it starts sputtering, spitting black smoke and shutting off at idle. I’ve got that other running M12 if needed though. 1 4 Share this post Link to post Share on other sites
702854boy 1,053 #26611 Posted 15 hours ago 32 minutes ago, Syrmore said: Why's that deck look wide? Share this post Link to post Share on other sites
adsm08 4,864 #26612 Posted 13 hours ago 1 hour ago, 702854boy said: Why's that deck look wide? The whole image looks skewed, like maybe it was taken with a wide-angle lens. Share this post Link to post Share on other sites
Bill D 3,025 #26613 Posted 13 hours ago (edited) 10 hours ago, ML3 said: Got the Bervac swapped onto 416. Also swapped rear hitch, larger wheels/tires from Workhorse. Still have a few more preventive maint items to get done. Got lift assist springs installed/adjusted & 150lbs of weight on hitch. Now I gotta figure out what to do with the Workhorse. Be nice to have it for parts but dont really want it sitting around...... 20260814_133023.mp4 Definitely worth repowering your Work Horse in that condition. I have an engine here, but no good way to get it to you. There are NOS engines on ebay. Old Craftsman tractors may also yield a usable engine. Edited 13 hours ago by Bill D 1 Share this post Link to post Share on other sites
ebinmaine 79,896 #26614 Posted 2 hours ago 10 hours ago, Bill D said: Definitely worth repowering your Work Horse in that condition. I have an engine here, but no good way to get it to you. There are NOS engines on ebay. Old Craftsman tractors may also yield a usable engine. @ML3 The Workhorse GT1800 we built for our friends had a Craftsman engine swapped in. Direct bolt 🔩 in replacement. Super common tractors too. Share this post Link to post Share on other sites
ML3 2,438 #26615 Posted 1 hour ago 43 minutes ago, ebinmaine said: @ML3 The Workhorse GT1800 we built for our friends had a Craftsman engine swapped in. Direct bolt 🔩 in replacement. Super common tractors too. Been searching since Oct of last year for an engine w/no luck.....and yes looked for Craftsman engines too. Even tried to find a Kohler, Vanguard too. Im out a lot less $$, time, & aggravation with the 416. Was gonna part out 1848 but dont want a dead tractor sitting around. Probably just sell it cheap & hopefully with the 37" deck too. Just really want it out of the way. I live in town so space is limited 1 Share this post Link to post Share on other sites
