Jump to content
Sign in to follow this  
Followers 0
Hukah

finding finishing touches 552

By Hukah, in Restorations, Modifications, & Customizations

Recommended Posts

Hukah    17

Hukah
Posted

I need to find the trans cover (rubber boot for bottom of shifter) to finish my 552 restore project.
(Is there a sourcing link for aftermarket components?)
Anybody know where I can check?

Thanks.

  • Like 1

Share this post

Link to post
Share on other sites
 

ACman    7,557

ACman
Posted (edited)

@Hukah:techie-ebay: Has them around $10.00 . :wwp: :text-thankyoublue:

Edited by ACman
  • Like 2

Share this post

Link to post
Share on other sites
 

Hukah    17

Hukah
Posted

Thank ACman.
I didn't see any with a round base like I had.
 

  • Like 1

Share this post

Link to post
Share on other sites
 

ACman    7,557

ACman
Posted

Or you can try Stiener tractor parts . There located in Lennon Mi , type in shifter boot in there search box something will pop up . It's fun looking at all the parts they have anyways .

  • Like 2

Share this post

Link to post
Share on other sites
 

Hukah    17

Hukah
Posted

Now THAT'S what I was looking for.
Found it in no time, thanks a lot.

  • Like 2

Share this post

Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  
Followers 0
Go To Topic Listing

  • Similar Content

    • Hukah
      3/4inch shaft
      By Hukah
      I need to re-power my 552.
      The only thing I can afford is a 3/4 shaft job.
      I know I'll have to change pullies, but am I going to run into problems, seeing as the original was a 1 inch shaft?
    • Hukah
      Engine swap and mod
      By Hukah
      I bought a great engine of CL for $20 (Briggs 5.5hp).
      it was on a snowblower, however, and has no throttle or choke control from the driver seat.
      i got a choke control hooked up, but the throttle control is being finicky.
      i am mechanically apt, but not familiar with all the different intricacies of different units and I'm assuming the way this type of engine works is interfering with my new linkage I installed?
      anybody got any tips I can try to get this working properly?
    • Hukah
      552 drive belt size?
      By Hukah
      Sorry for all the 'newbie' questions, guys, but no one has told me to take a hike yet so I'll push my luck with another (likely) redundant question; What is the correct drive belt size for my 552, anybody know?
      And an aside; Does the mower deck operate on the same drive belt, or is that going to be a 'take-off' pulley next to it (I am painting it so I can't align it up to tell ATM).

      Thanks again.
    • Hukah
      H55 wiring
      By Hukah
      I am going to rebuild my H55.
      i am taking pics to remind me where it goes and what it looks like, but the fuse block had been disconnect years before I got it.
      can someone explain the wiring to/from this block?
      is it possible to put lights on this electrical system?
       
      iver just about got this thing back on the job thanks to you all.
       
      i just tried to upload a pic and it won't let me.
      ill post one from my computer soon.
    • Hukah
      Lettering tips?
      By Hukah
      Now that I've got the red and black painted, I'm painting the whites and just now getting cold feet while looking at the bas-relief WHEELHORSE lettering across the top of the grill.
      any tips/pointers as to the best approach to this task?
       
      Thanks for all the help you guys bring, I don't think I could have gotten this far without you.
×
×
  • Create New...