JERSEYHAWG / Glenn 4,487 #26 Posted September 12, 2015 I knew Craig was fast. but WOW!Glenn 1 Share this post Link to post Share on other sites
Terry M-(Moderator) 2,125 #27 Posted September 12, 2015 Craig, if you need one of those round tecky air cleaner covers....I got one for you..Just noticed it wasn't on there. Share this post Link to post Share on other sites
slammer302 2,154 #28 Posted September 13, 2015 I like the way those little tecumseh powered horses ride and drive with skinny tires and the steering is usually pretty good on them too for sum reason 1 Share this post Link to post Share on other sites
Retired Wrencher 4,879 #29 Posted September 13, 2015 Pretty much, all back together now... just got a no spark issue to deal with...but I think it's because of the mouse hotel all packed in behind the engine tins. Just had to call the game because of rain. Wow Craig Less than 12 hours and she is ready to work. The spark is easy fix parts are cheap Just saying from one Tecky person to another. But I found out that the notch on the cheap coils are junk = the notch on top of the coil is not high enough to hold the clip in place. that is what happen when I bought one. so went to a oem part. Enjoy looks like you are almost there. I have an extra dash if you need one. Share this post Link to post Share on other sites
AMC RULES 36,945 #30 Posted September 14, 2015 Welp... it's back to being a roller again. Popped the blower housing off today...see if I could get away easy, just clean out the nest.found the back of it was chock full of nest, to include one dried up mouse. Decided to romove the flywheel...only to find one of the magnets missing too. Going to take the block to work with me tomorrow, give it a steam bath. Never had to venture this far into one to get it running... is the missing magnet is going to be issue...run again, with one of 'em missing? 2 Share this post Link to post Share on other sites
953 nut 51,725 #31 Posted September 14, 2015 Had a mower years back that had no spark after a long winter storage, turned out the points gap was open when stored and a bug nest under the flywheel held them open. Wish all my problems were that easy to solve. 1 Share this post Link to post Share on other sites
AMC RULES 36,945 #32 Posted September 14, 2015 If nothing else... I'll get this one cleaned up, put back together...give it a yank, and see what happens. At this point, I've got nothing to lose here. 2 Share this post Link to post Share on other sites
squonk 38,938 #33 Posted September 14, 2015 I believe you will need the missing magnet. Share this post Link to post Share on other sites
AMC RULES 36,945 #34 Posted September 14, 2015 Know of a source for missing magnets Mike? 1 Share this post Link to post Share on other sites
Terry M-(Moderator) 2,125 #35 Posted September 14, 2015 I believe you will need the missing magnet. Know of a source for missing magnets Mike? I see the magnet.....is there a way to glue these on?? 1 Share this post Link to post Share on other sites
AMC RULES 36,945 #36 Posted September 14, 2015 (edited) OH...is that it there attached to to other? No wonder, all the other flywheels I saw...only had two on 'em. Good eye Terry...should epoxy back into place, no problems. Edited September 14, 2015 by AMC RULES 2 Share this post Link to post Share on other sites
woodchuckfarmer 333 #37 Posted September 14, 2015 JB Weld works good for that. 2 Share this post Link to post Share on other sites
Terry M-(Moderator) 2,125 #38 Posted September 14, 2015 Your welcome Craig....tecumseh H60 and HH60 manual /pull start only engines use only two magnets. 1 Share this post Link to post Share on other sites
slammer302 2,154 #39 Posted September 14, 2015 I think i have a flywheel if that one doesn't work out for you 1 Share this post Link to post Share on other sites
AMC RULES 36,945 #40 Posted September 14, 2015 You guys are the best. 1 Share this post Link to post Share on other sites
Retired Wrencher 4,879 #41 Posted September 14, 2015 JB Weld works good for that. I was thinking the same thing get good and clean put some J.B. on it should be fine. Liquid steel a farmers friend. Good stuff. 2 Share this post Link to post Share on other sites
AMC RULES 36,945 #42 Posted September 15, 2015 Baby steps today...engine cleaned up, magnets back in place. Allow 24hrs to dry...then we'll see if the little indian that could, actually will run again. 4 Share this post Link to post Share on other sites
JERSEYHAWG / Glenn 4,487 #43 Posted September 15, 2015 Be great to see that motor run. Craig. You can do it. It was complete. Wish I had the gumption. But more important stuff to deal with. Mike and Johnny are over my shoulder peeking.Glenn 1 Share this post Link to post Share on other sites
AMC RULES 36,945 #44 Posted September 16, 2015 We'll make 'em have a dunk contest Glenn...to see who gets the first ride. 1 Share this post Link to post Share on other sites
Theroundhousernr 589 #45 Posted September 16, 2015 When you said never had to venture this far to get one running. I'm thinking most of mine start out like that lol. Not all but most. Can't wait to see what you do with this one. You have a knack with making the work close on an old horse look good. 2 Share this post Link to post Share on other sites
AMC RULES 36,945 #46 Posted September 16, 2015 Figured I try to get it back to factory specs first... but admit, I'm struggling with the notion to do something custom with it though. Guess we'll see how it goes...huh? 2 Share this post Link to post Share on other sites
JERSEYHAWG / Glenn 4,487 #47 Posted September 16, 2015 Your the boss. Whats your pleasure.....Glenn 1 Share this post Link to post Share on other sites
AMC RULES 36,945 #48 Posted September 16, 2015 Only natural, to want it both ways Glenn. Share this post Link to post Share on other sites
AMC RULES 36,945 #49 Posted September 27, 2015 (edited) Was gifted once again today... new plug, points, condenser, and with the third pull...the 500 Special's good little Techy came back to life. Edited September 27, 2015 by AMC RULES Share this post Link to post Share on other sites
slammer302 2,154 #50 Posted September 27, 2015 you got it made now 1 Share this post Link to post Share on other sites