SpillerMiller 10 #1 Posted November 27, 2013 I've been fighting with this old girl ever since I bought her in october. Got the snowblower working properly, fixed hydraulic leak, rebuilt starter, and now a previous owner before me cobbled up some abortion on my right side drive tire. The axle spun inside the hub, binding the square key which proceeded to blow the cast hub apart. I need to find a replacement fast because winter is upon us in Mid-Michigan and i have a to bog of a drive way to shovel. Anyone know where to get one and how much they usually cost? Any and all help and/or advice is appreciated. Thank you Sent from my SCH-I535 using Tapatalk Share this post Link to post Share on other sites
AMC RULES 37,196 #2 Posted November 27, 2013 (edited) Look in the vendors section here...member Kelly is up there by you... or Ebay search "wheelhorse hub" and see what you come up with there. http://www.wheelhorseforum.com/user/85-kelly/ Edited November 27, 2013 by AMC RULES Share this post Link to post Share on other sites
SpillerMiller 10 #3 Posted November 27, 2013 Here are some pictures of the intact one to show what I need. It is a hydro-stat drive. I don't think that'll make a difference, but just getting all the information out there to get the best answers. Sent from my SCH-I535 using Tapatalk 1 Share this post Link to post Share on other sites
boovuc 1,090 #4 Posted November 27, 2013 Spiller, Please post what tractor you have. It would also help if you could let everyone know what diameter your axles are. (inch or inch and an eighth). Many guys have hubs we can get to you. Share this post Link to post Share on other sites
SpillerMiller 10 #5 Posted November 27, 2013 Ok, thank you AMC Sent from my SCH-I535 using Tapatalk Sorey boovuc. It is a C-160 Auto Sent from my SCH-I535 using Tapatalk 1 Share this post Link to post Share on other sites
SpillerMiller 10 #6 Posted November 27, 2013 1 1/8" I believe Sent from my SCH-I535 using Tapatalk Share this post Link to post Share on other sites
boovuc 1,090 #7 Posted November 27, 2013 All I have are inch spares. Sorry! Dave or Kelly among others have them. Post a wanted in our classified section. 1 Share this post Link to post Share on other sites
SpillerMiller 10 #8 Posted November 27, 2013 I have the blown hub at work. Ill get an accurate maesurement tomorrow so we'll know for sure, but I'm quite certain its 1 1/8" Sent from my SCH-I535 using Tapatalk Share this post Link to post Share on other sites
SpillerMiller 10 #9 Posted November 27, 2013 Its coming out between 1 1/8" and 1 3/32. But it looks "egged out". I'm going to say 1 1/8" Sent from my SCH-I535 using Tapatalk Share this post Link to post Share on other sites
gwest_ca-(File Mod) 11,490 #10 Posted November 27, 2013 Save that old worn hub so you can make a hub puller out of it. Garry Share this post Link to post Share on other sites
SpillerMiller 10 #11 Posted November 27, 2013 Garry, how would I go about doing that? Sent from my SCH-I535 using Tapatalk Share this post Link to post Share on other sites
Kegler 68 #12 Posted November 27, 2013 While I had it apart I would probably put in a new axel seal. Good time to elininate a possible future problem. Share this post Link to post Share on other sites
SpillerMiller 10 #13 Posted November 27, 2013 All good info. Thank you. Keep the help and advice coming. Sent from my SCH-I535 using Tapatalk Share this post Link to post Share on other sites
AMC RULES 37,196 #14 Posted November 27, 2013 Does it have one or two seperate set screws on it? Share this post Link to post Share on other sites
