Jump to content
Sign in to follow this  
jasoncracer

Carb help

Recommended Posts

jasoncracer

my c160 inside the bowl has a line like.if the fuel sat there and ate it away tractor runs great new plug,points one problem getting a little spudder every once in a while carb is clean no play in shaft clean filter. :hide:

whats that line could that cause a spudder or maybe a bad bowl seal I fine adjusted carb for hours no luck?

20110608210842.jpg

Uploaded with ImageShack.us

Share this post


Link to post
Share on other sites
 
Jim_M

No offense intended, but from the look of that bowl the carb is not clean. I would take it apart and soak it in carb cleaner overnight, blow it out, reassemble it and try it again.

Share this post


Link to post
Share on other sites
 
jasoncracer

Will try the stuff on bottom of.bowl.wont come.off also if you look at high idle needle.valve from bowl.side as you turn it its not 100% straight will that do it

Share this post


Link to post
Share on other sites
 
smoreau

I agree with Jim M on this one, that bowl isn't clean. It should be all aluminum insde, not black stuff. I bought a 1 gallon can of dip carb cleaner with a basket in it for $15 from O'Riellys and have cleaned 5 carbs with it and the come out spotless after 24 hours. It has paid for it self in the amount of carb spray I have saved. Best of all the can is still full and should be able to clean many more carbs.

Share this post


Link to post
Share on other sites
 
jasoncracer

Thanks working at toro now they have this system it vibrates its got a solution in it heats up. leave carb in it for a little looks like new when its all done.

Share this post


Link to post
Share on other sites
 
Shuboxlover

Thanks working at toro now they have this system it vibrates its got a solution in it heats up.

Congrats on the job....are you talking about an ultrasonic cleaner??? If so, we use those at work to clean some of our parts that are particle sensitive, they do a FANTASTIC job!!! :hide:

Share this post


Link to post
Share on other sites
 
shallowwatersailor

HF sells a nice ultrasonic unit that is not too expensive. It works wonders on what you need cleaned.

Share this post


Link to post
Share on other sites
 
wheelhorsec85

my c160 inside the bowl has a line like.if the fuel sat there and ate it away tractor runs great new plug,points one problem getting a little spudder every once in a while carb is clean no play in shaft clean filter. :hide:

whats that line could that cause a spudder or maybe a bad bowl seal I fine adjusted carb for hours no luck?

20110608210842.jpg

Uploaded with ImageShack.us

JASON JUST BUY A NEW BOWL . that bowl is garbage . once they get eaten through like that it will continue to happen . new bowls are cheap :) :WRS:

Share this post


Link to post
Share on other sites
 
.5racer

What did you set the points at ? CLEAN that bowl with steelwoole and blast that carb with some cleaner, with a new carb gasket set and reassemble, adjust and set . Good Luck :hide:

Share this post


Link to post
Share on other sites
 
shorts

the ring around the bowl is from a combination of water and hi alcohol content gasohol being left in the carb foe an axtended period, :hide::hide: kinda like not draining the carb when winterizing :WRS::beer::disgust: ,been there done that,more than once :):) anyhow,replace the bowk,check the float for damage from being frozen"partially collapsed/crushed" replace it also if necessary, check and thorougly clean the hi speed jet and fuel pickup passages in the stem that the bowl bolts to. sometimes a quick soak in vinegar and then baking soda solution will clean out serious corrosion in a carb. then clean with carb spray and compressed air before assembly

Share this post


Link to post
Share on other sites
 
can whlvr

i too have used the ultrasonic cleaners,they work unbeileivable,it vibrates and heats up hot soapy water i did my 30 year olr sthil weedwacker and it runs like new,i borrowed it and would buy one in a flash,the one i used was about 500 bucks,but for that much cash a can get more horses

Share this post


Link to post
Share on other sites
 
72morph

Please check point gap as it cost me a lot of money and aggravation. :hide: Try 15 to 18 .

Share this post


Link to post
Share on other sites
 
puddlejumper

Not to disagree with everybody because its all valiod points. But you have done this several times and you say its clean maybe stained but clean. Your occasionall miss could be a faulty spark plug or condensor. OR even a plug wire shorting occassionally.

I know you said you replaced these items but stranger things have happened.

Share this post


Link to post
Share on other sites
 
tommy3horse

Hello Jason;

Kohler has the points set @ .020, plug @ .025. Main needle must be VERY clean too. Good luck.

Tom

:hide:

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×
×
  • Create New...