Jump to content
Emann

300/400 series seat mount cracks: where did yours break?

Recommended Posts

Emann

Hey all, new here. I do CAD and sheet metal for a living and I've been reading about seat and tank mounts cracking on the 300 and 400 series. If yours cracked, I'd love to know:

1. Which model and year?

2. Where exactly did it crack? A photo would be awesome.

3. How did you fix it: weld, angle iron, washers?

4. Would a bolt-on, no-weld fix be useful, or is everyone just welding them?

Thinking about designing something. Thanks!

  • Excellent 3

Share this post


Link to post
Share on other sites
 
Ed Kennell

:text-welcomeconfetti:to the :rs:

Share this post


Link to post
Share on other sites
 
Sparky

I had a few of mine crack..a buddy of mine welds em up. 
  Latest one was my 83 C-145 auto. The missing piece on the left side I had,

so it was welded back in. The other side was cracked only.


 

IMG_9088.jpeg

 

IMG_9105.jpeg

 

 

  • Like 2

Share this post


Link to post
Share on other sites
 
953 nut

:WRS:

I have had the same issue as Mike showed pictures og but I just used a piece of thin angle iron inserted below and bolted in place.

  • Like 1

Share this post


Link to post
Share on other sites
 
ri702bill

Over the summer I had 2 identical C81's apart to choose the better pieces.... I ended up removing the three spot welds on both hoodstands and did a mix-n-match as one has a better right half, the other the left side was better. That gave better access to measure & weld. Fabbed up some 1/8 steel angle pieces to weld in underneath as reinforcements. Rejoined the halves with four steel pop rivets. Better than new...

 

 

 

 

P1010186.JPG

P1010187.JPG

P1010188.JPG

P1010189.JPG

  • Like 5
  • Excellent 2

Share this post


Link to post
Share on other sites
 
sqrlgtr

The last 312-8 I was working on had began to crack where @Sparky has pictured and i used fender washers to stiffen up, only because I was out of welding wire :angry-banghead:. if/when I am back in there will try and weld up the cracks and add somthing like @ri702bill has done. that looks like it would really take care of problem. I have only seen one tractor in this series that was not starting to crack, so must be a very common problem with the 300,400,500 series of tractors.

  • Like 1

Share this post


Link to post
Share on other sites
 
peter lena

@ri702bill  nice save , also watch out  , purists  say  you can't do that , done a lot of  functional detailing  , enhancing  as I went , KEPT GETTING  BETTER , also  went to  shoulder  type , bolts , no threading , in swing point , held   flat washered , elastic  Lok nut .  paint  it  red / black , it disappears ,  good job , pete 

  • Like 1
  • Excellent 1

Share this post


Link to post
Share on other sites
 
oliver2-44

:text-welcomeconfetti:

The No Names, C 1xx  (100, 120, 160 Series has a little seat cracking. The C1x1 (101, 121, 141, 161) C1x5 105,125,145,165) is more like the 300 Series and cracking is common.

I have a C1x1 cracked and  I'll get a picture of it

I have a stick welder, but can't weld thin sheet metal with it.

So a non-weld repair would be nice for many of us. 

Edited by oliver2-44

Share this post


Link to post
Share on other sites
 
ri702bill

Can you braze it?? Basicily glueing it together with molten flux coated brass rod....

Share this post


Link to post
Share on other sites
 
Emann

Thank you all for the warm welcome, and for all the replies. This is super helpful! @oliver2-44, I'd love to see a picture of your cracked C1x1 when you get a chance. And if anyone can share measurements around the crack area, that would help a ton.

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...