CCW 1,521 #1 Posted Thursday at 03:28 PM (edited) The 36 in RD mower deck on my 312-8 is nearly 40 years old. It has always been garage and the shell is as solid as the day it was bought. Over the past couple of years I have been adding grease via the zerks and all appears to work great though it is very loud while engaged. My concern is the grease at the bearings. Does it dry out that new grease may not be reaching the bearings? How do I know if I have added enough grease? Or is this a case of if it ain't broke don't fix it? I hate to disassemble the deck if there is no sure benefit. Edited Thursday at 03:28 PM by CCW Share this post Link to post Share on other sites
8ntruck 9,411 #2 Posted Thursday at 04:14 PM It is probably time to disassemble the spindles. If you have noise that wasn't there in the past, something has changed - a bad bearing, a worn shaft, etc. Check the spindles individually for smooth rotation, end play, and radial play. That should give you a clue as to which one is the worst, therefore the one to start on. Remember, all the spindles have been in service the same amount of time. If one is bad, the others probably are reaching the end of their service life too. I've got three decks that I need to have that done. 3 Share this post Link to post Share on other sites
gwest_ca-(File Mod) 12,543 #3 Posted 22 hours ago If you remove the spindle belt and feel and spin each pulley you may find they don't feel or sound the same. A good first step in your inspection. Find a bad one then make the necessary repairs followed by another spin comparison. By now you will know what a good spindle assembly sounds like. 2 Share this post Link to post Share on other sites
953 nut 70,435 #4 Posted 5 hours ago This old thread may be helpful. Share this post Link to post Share on other sites
peter lena 10,115 #5 Posted 5 hours ago @CCW , ben using lucas xtra hd green chassis grease , in every , CLEANED OUT bearing , for years , walmart $ 8, my mower decks and related pto bearings , spin with silent ease . bearing whine and roughness is telling you of failure , also related to belt fraying / cracking , many years in no failures , pete Share this post Link to post Share on other sites
953 nut 70,435 #6 Posted 5 hours ago On 11/19/2026 at 11:14 AM, 8ntruck said: I've got three decks that I need to have that done. When you do the bearing replacement PLEASE do a Tutorial thread with lots of pictures, list of tools needed, and part numbers. There is very little useful information on this subject that has been posted. Share this post Link to post Share on other sites
Brockport Bill 2,519 #7 Posted 3 hours ago i have rehabbed numerous decks and spindles -- new bearings installed etc -- not my favorite job but something worth doing -- removing and re--installing the snap ring and getting out the old bearings and tube is not fun but is a learned skill. there are some You Tubes but maybe not WH but all same principle --- the key factor to understand is unless the bearing has one rubber seal removed, then the grease for zerk doesn't really lube the ball bearings inside the bearing. A 2 sided seal is in fact a "sealed" bearing. last point, if you ever need spindles, or spindle parts like a shaft, pulleys etc, I have always been happy with K&B in pennsylvania for help - good service and prices. attached photos of spindle project - rebuilt bearings and painted etc as one fyi -- to remove the tube and lower bearing i first remove snap ring - - then i use a long socket that fits inside the top bearing -- i then use hammer to hit the socket and drive the tube down onto lower bearing to "punch" it out - once the lower bearing is out then i insert socket from bottom to hammer tube to knock out top bearing. have paper towels near by for all the grease!!! have fun !!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Bill Share this post Link to post Share on other sites