Jump to content
FLtractor

856 Crankshaft pulley questions

Recommended Posts

FLtractor

Evening,

 

Just making sure.. the proper factory sized 856 crankshaft pulleys for transmission and belt drive off crankshaft.. both are 4 inch diameter with 1 inch bore? What size woodruff key needed?

Share this post


Link to post
Share on other sites
 
ebinmaine

The engine pulley is a 2" outer diameter. 

 

The transmission pulley I believe is 4" but the internal bore is much smaller. 

Either 5/8 or 3/4 inch. 

 

What prompts the question? 

 

 

 

 

Share this post


Link to post
Share on other sites
 
FLtractor
1 hour ago, ebinmaine said:

The engine pulley is a 2" outer diameter. 

 

The transmission pulley I believe is 4" but the internal bore is much smaller. 

Either 5/8 or 3/4 inch. 

 

What prompts the question? 

 

 

 

 

Evening Eric, I just went outside with a tape measure to double verify. Measuring across lengthway thru the center of the crankshaft

picture attached of pulley measured:

Top 2 pulley on engine crankshaft= 2 1/2 inch

     Middle and bottom = 3 inch each. 
Ask since I was told my flywheel belt is wrong being fabric.. can cause glazing with the slipping and should be the ribbed belt on one side.. well after looking at all my belts they are all fabric and all very old need to get new ones. . should I change them all too ribbed one side? Pulleys seems to be glazed due to this and should be replaced at this time too.. easier all at once. 

IMG_5263.jpeg

Share this post


Link to post
Share on other sites
 
ebinmaine
11 minutes ago, FLtractor said:

Ask since I was told my flywheel belt is wrong being fabric.

 

Are you talking about the green transmission drive belt?

 

 

Share this post


Link to post
Share on other sites
 
953 nut

You are looking at the wrong side of the engine.. The Starter / generator belt should be a 3/8" wide rubber edge cogged belt 3L-32  NAPA # 25-7315

Share this post


Link to post
Share on other sites
 
FLtractor
35 minutes ago, ebinmaine said:

 

Are you talking about the green transmission drive belt?

 

 

Already have new S/G cogged belt I need… Need to replace both my transmission and that deck drive belt connected to the 3 pulleys. Need to know are both the transmission and 3 pulleys connected deck drive belt need to be cogged belts too?

Edited by FLtractor

Share this post


Link to post
Share on other sites
 
FLtractor
28 minutes ago, 953 nut said:

You are looking at the wrong side of the engine.. The Starter / generator belt should be a 3/8" wide rubber edge cogged belt 3L-32  NAPA # 25-7315

Yes I know.. I have the new cogged belt already.. do the transmission belt and deck drive 3 pulley connected belt need to be cogged belts too instead of fabric? Have item numbers for those two by chance?

Share this post


Link to post
Share on other sites
 
ebinmaine
48 minutes ago, FLtractor said:

Ask since I was told my flywheel belt is wrong being fabric.. can cause glazing with the slipping and should be the ribbed belt on one side.

 

The flywheel to generator belt should not be fabric. 

 

The transmission belt MUST BE FABRIC COATED. 

 

The green belt is fabric coated and NEEDS to be able to slip. 

It is literally the clutch of the machine. 

 

 

  • Excellent 1

Share this post


Link to post
Share on other sites
 
pfrederi

The mower deck belts (3) can be fabric covered as also the transmission drive belt.    Honestly  I have units running with belts looking a lot worse than yours and they work just fine.

  • Like 1
  • Excellent 1

Share this post


Link to post
Share on other sites
 
ebinmaine
51 minutes ago, FLtractor said:

should be the ribbed belt

 

IMHO that's not necessary as long as the proper length RUBBER belt is used. 

  • Excellent 1

Share this post


Link to post
Share on other sites
 
FLtractor
10 minutes ago, ebinmaine said:

 

The flywheel to generator belt should not be fabric. 

 

The transmission belt MUST BE FABRIC COATED. 

 

The green belt is fabric coated and NEEDS to be able to slip. 

It is literally the clutch of the machine. 

 

 

Ahhh so 1/2x70 transmission belt must be fabric due to how it slacks everytime clutch depressed.. makes sense. Thanks Eric 

Share this post


Link to post
Share on other sites
 
FLtractor
10 minutes ago, pfrederi said:

The mower deck belts (3) can be fabric covered as also the transmission drive belt.    Honestly  I have units running with belts looking a lot worse than yours and they work just fine.

Oh ok. Good to know. Do you happy to have a parts # or what size belt I need for the mower deck 3 belt if I were to eventually replace it?

Share this post


Link to post
Share on other sites
 
FLtractor
10 minutes ago, ebinmaine said:

 

IMHO that's not necessary as long as the proper length RUBBER belt is used. 

Wouldn’t think people would use other materials such as cloth? 

Share this post


Link to post
Share on other sites
 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...