Cee245 874 #1 Posted Wednesday at 12:01 AM (edited) Well, this has never happened to me before... I work 3rd, and woke up recently in the afternoon to a voicemail and a free 416-8 in the back yard! My father in laws buddy gave me a 1990 416-8 with the Onan. Now, its not anything too special, but my teenage sons amd I should be able to get it going. Story is and from what i can tell by quickly looking it over, the guy bought a Chinese carb and hasn't been able to keep it running. It has ~525hrs on a probably non working meter and was left for dead. (It is One of those tractors where you can "see" the mouse nest behind the engine shroud. LOL) But there are still lots of good usable parts. Its rusty, but metal is straight, so I'm thinking of using this hood at least. PLAN: This machine is (i think) identical to the 1991 416-8 my dad bought new. I have that tractor and will basically combine those two into one decent unit. All in all, I wont need to purchase too much to make it a decent unit. Just LOTS of grease and rewiring obvious issues. Edited Wednesday at 12:03 AM by Cee245 7 5 Share this post Link to post Share on other sites
953 nut 70,260 #2 Posted Wednesday at 01:27 AM My favorite four letter word, FREE 3 2 Share this post Link to post Share on other sites
ebinmaine 81,116 #3 Posted Wednesday at 09:36 AM Nice gift! Share this post Link to post Share on other sites
702854boy 1,199 #4 Posted Wednesday at 01:49 PM It looks like the mower belt might be in the wrong groove on the clutch bell. 2 Share this post Link to post Share on other sites
Cee245 874 #5 Posted Thursday at 01:04 PM (edited) Good catch! It sure is. It's getting tossed along with most of the deck. It is pretty beat. Several large rust holes. Hopefully i can salvage a few things like spindles. Edited Thursday at 01:06 PM by Cee245 Share this post Link to post Share on other sites
Bill D 3,191 #6 Posted Thursday at 01:51 PM 45 minutes ago, Cee245 said: Good catch! It sure is. It's getting tossed along with most of the deck. It is pretty beat. Several large rust holes. Hopefully i can salvage a few things like spindles. I like to run decks like that until they are completely unusable. Save the wear and tear on the good ones. 1 Share this post Link to post Share on other sites
rjg854 13,419 #7 Posted Thursday at 02:01 PM As long as decks work as they should and still give a nice cut, a good, experienced welder can take care of any holes. 1 Share this post Link to post Share on other sites
Cee245 874 #8 Posted 4 hours ago (edited) Thanks... for me, thats the issue. No welder amd limited experience. You're right though, it just is ugly. No reason I can't grease and oil it to keep it solid for longer and just cut grass! I Found out that I am 2nd owner. I've gone over it a bit and to my surprise, it's actually in pretty decent shape overall. Even seat switch works! All original tires hold air and have the wear id expect for hrs shown. The meter says 527 or so and it appears to be accurate. Just left outside under a lean to. From what I've seen the 6" tires seem to get bald by 800 hrs. The 8" generally have ok tread at 1000 hrs/use. I set valve clearances. Popped off flywheel and cleaned. Need to decarbon heads and find a new ignition switch. I dont know how this actually works with all the corrosion. The engine shroud had the obligatory mouse nest for a low cost machine lol. Ordered full gasket set and will need a few other things as I have time to work on it. Edited 2 hours ago by Cee245 Spaced pictures apart 1 Share this post Link to post Share on other sites
ebinmaine 81,116 #9 Posted 1 hour ago 2 hours ago, Cee245 said: Ordered full gasket set and will need a few other things as I have time to work on it. Great to see it getting the maintenance deserved! Share this post Link to post Share on other sites