WHX?? 57,720 #1 Posted 13 hours ago So @Achto and I were at show and had a little gravel pile to play in with our mid mounts & blades & loaders. I had brought this pusher rear mount to play with but neglected to bring along a axle bracket. No big deal I'll just one off of pale face Dan's 856. Well this wasn't gonna work. I had thought all brackets were the same. What bracket to I need to run this? 1 1 1 Share this post Link to post Share on other sites
ri702bill 12,777 #2 Posted 13 hours ago That is a later style Grader blade - the "push" style. It requires the later C series, 300, 400 bracket. The "pull" style required no axle bracket - it mounted to the mid Tach-a-matic frame mounts like a cutting deck. 3 1 1 Share this post Link to post Share on other sites
ebinmaine 80,243 #3 Posted 13 hours ago 21 minutes ago, WHX?? said: So @Achto and I were at show and had a little gravel pile to play in with our mid mounts & blades & loaders. I had brought this pusher rear mount to play with but neglected to bring along a axle bracket. No big deal I'll just one off of pale face Dan's 856. Well this wasn't gonna work. I had thought all brackets were the same. What bracket to I need to run this? Jim. That axle bracket is for a SHORT frame plow. You need the one that faces downward. Without bolting on the front as this one does. 2 1 1 1 Share this post Link to post Share on other sites
Lane Ranger 12,081 #4 Posted 13 hours ago (edited) Jim : I think the older rear axle bracket was made for a short frame snowplow and it has a wider rod on the snowplow (or locks on the outside portions of the rod on the snowplow). You need the newer version of a rear axle bracket that has a more narrower length on the lock in clamps. Anyway that is my understanding but I sold my version of your mid grader blade and just have the early version now for my round hood tractors. The rear axle hitch you have is 15 1/2 inches wide on the install locks. The newer Wheel Horse/Toro version is 11 inches wide. The old style mid grader blade rear 3/4 rod attached to plates on the side of the frame of a Wheel Horse. Your version, the much stronger , wider and better operating Mid Grader blade attached to the rear hitch but with a more narrow set of locking arms! The last three pics are of the old style rear axle hitch (this. one for a HY hydraulic lift cylinder installation). Edited 13 hours ago by Lane Ranger 4 2 1 Share this post Link to post Share on other sites
WHX?? 57,720 #5 Posted 12 hours ago 37 minutes ago, ri702bill said: "pull" style required no axle bracket - it mounted to the mid Tach-a-matic frame Yep well versed in those ... I think I have one of those "short" brackets on a winter 520 that was used for a tiller. Maybe that one will work? Will have to look when she comes out of storage for snow duty. 2 5 Share this post Link to post Share on other sites
squonk 47,873 #7 Posted 11 hours ago Robbing parts off of Dan's tractors when he aint lookin! We don't wanna hear any whinin when one of your tractors is suddenly missin an engin! 7 1 Share this post Link to post Share on other sites
peter lena 10,003 #8 Posted 10 hours ago @Achto that paint fade and dried out seat would look in perfect PATINA STAGE , with little work , mothers back to black , vinyl / plastic for seat , penetrating oil , spray down let it sit for days / weeks , wipe down with a clean cloth / mineral oil , no scratch pads or paint scrubbing , done a lot of that , with good results , deep solid oiled finish . just my thought , pete 2 1 Share this post Link to post Share on other sites
rjg854 13,299 #9 Posted 5 hours ago 6 hours ago, squonk said: Robbing parts off of Dan's tractors when he aint lookin! We don't wanna hear any whinin when one of your tractors is suddenly missin an engin! Mafia eating their own 4 Share this post Link to post Share on other sites
SylvanLakeWH 32,100 #10 Posted 4 hours ago 10 minutes ago, rjg854 said: Mafia eating their own Typical cheese curd tactic up Nord... 4 Share this post Link to post Share on other sites
WHX?? 57,720 #11 Posted 2 hours ago 8 hours ago, squonk said: Robbing parts off of Dan's tractors when he aint lookin! I gave him the tractor 'cause I already have a 856 so what comes around goes around. Thanks Ed Dog ... I took a peek at the one on a 520 and all I could see is it did bolt from the top so I think it's the one. She is strictly a snow machine now the way she is decked out put I did till with it at one time. 3 1 Share this post Link to post Share on other sites
peter lena 10,003 #12 Posted 2 hours ago @Achto that paint fade and dried out seat would look in perfect PATINA STAGE , with little work , mothers back to black , vinyl / plastic for seat , penetrating oil , spray down let it sit for days / weeks , wipe down with a clean cloth / mineral oil , no scratch pads or paint scrubbing , done a lot of that , with good results , deep solid oiled finish . just my thought , pete Share this post Link to post Share on other sites
peter lena 10,003 #13 Posted 1 hour ago @Achto that paint fade and dried out seat would look in perfect PATINA STAGE , with little work , mothers back to black , vinyl / plastic for seat , penetrating oil , spray down let it sit for days / weeks , wipe down with a clean cloth / mineral oil , no scratch pads or paint scrubbing , done a lot of that , with good results , deep solid oiled finish . just my thought , pictures , pete 1 Share this post Link to post Share on other sites
