Toolmanbill 47 #1 Posted June 23 You guys helped me out last year about upgrading tires.lucky for me that I took your advice. I purchased carlstar all trail 23x8x12 tires. They worked unbelievably well. I have since purchased another wheel horse 314-8 and would like to upgrade the tires for this as well. I noticed on Amazon they have 23x10.5x12 tires from Hoosier wheel that look very similar. The carlstar are 272$ and the Hoosier tires are 161$.hate to cheap out but at 111$ difference it’s tempting. also had plans to attend the big show on Friday . But the forecast is likely looking like rain.Thursday looks much better.is there anything going on then or should I just go Friday and dodge the raindrops? Share this post Link to post Share on other sites
ebinmaine 81,176 #2 Posted June 23 2 hours ago, Toolmanbill said: The carlstar are 272$ and the Hoosier tires are 161$.hate to cheap out but at 111$ difference it’s ******. I've run tires of all grades, several brands and sizes. Are you planning on keeping this tractor? If you know what you got from the other set and that was pleasing, get them. If it's just for resell... maybe try the cheapos? Share this post Link to post Share on other sites
Handy Don 17,684 #3 Posted June 23 (edited) 2 hours ago, Toolmanbill said: also had plans to attend the big show on Friday . But the forecast is likely looking like rain.Thursday looks much better.is there anything going on then or should I just go Friday and dodge the raindrops? By Thursday afternoon, the show will be quite busy. Larger vendors will have had time to set up; many smaller ones as well. Busiest day is Friday, for sure. Weather at previous shows has included epic downpours, wilting heat, and strong winds. Come prepared and just go with it. Edited June 23 by Handy Don Share this post Link to post Share on other sites
rjg854 13,425 #4 Posted June 23 4 hours ago, Toolmanbill said: Amazon they have 23x10.5x12 tires from Hoosier wheel that look very similar. The carlstar are 272$ and the Hoosier tires are 161$. I'd go for the cheaper tire, if they are somewhat comparable, in ply rating, and you don't mind a wider tire. Share this post Link to post Share on other sites
pfrederi 21,314 #5 Posted June 23 Unless you are running a commercial lawn service with your WH I would bet any tire would dry rot/crack before you wore it out. 1 1 Share this post Link to post Share on other sites
Toolmanbill 47 #6 Posted Wednesday at 11:50 AM Had so much luck buying these carlstar 23x8x12 tires I wanted to buy another set for this 2001 314-8 I purchased.took them to the local Goodyear store. They told me they couldn’t mount them without putting tubes in them.since I had these mounted on my 1994 model I just assumed that someone there didn’t know what they were doing.so I took them to the shop where I had the other ones mounted.he couldn’t mount them either.eventually had to put tubes in them as well.couldn’t find any information that wheel sizes had changed.any idea where I would find that info? Share this post Link to post Share on other sites
My_horse 143 #7 Posted Wednesday at 01:19 PM 1 hour ago, Toolmanbill said: Had so much luck buying these carlstar 23x8x12 tires I wanted to buy another set for this 2001 314-8 I purchased.took them to the local Goodyear store. They told me they couldn’t mount them without putting tubes in them.since I had these mounted on my 1994 model I just assumed that someone there didn’t know what they were doing.so I took them to the shop where I had the other ones mounted.he couldn’t mount them either.eventually had to put tubes in them as well.couldn’t find any information that wheel sizes had changed.any idea where I would find that info? What was the reason that they couldn’t mount them? Couldn’t get the beads to seat/seal? Share this post Link to post Share on other sites
Toolmanbill 47 #8 Posted Wednesday at 02:52 PM Yes.couldn’t get the beads to seal.what I saw was the tire was much narrower than the wheel. Share this post Link to post Share on other sites
pfrederi 21,314 #9 Posted Wednesday at 03:28 PM (edited) WH used at least 3 different width rear rims. 5, 7 and 8.5. Measure the distance from the center flange to the drop center edge (see picture) if it is about 1" you have 5 "wide rims if it is 3 you have 7 inch rims4-1/2 is 8.5 " wide rims. This assumes they all have the same Back set (1-3/8") I bet you have different wheels on your two tractors Pic one is a 5" rim the other 7" Last pic is 8.5" Edited Wednesday at 03:31 PM by pfrederi Share this post Link to post Share on other sites
cafoose 3,883 #10 Posted Wednesday at 06:29 PM 2 hours ago, pfrederi said: WH used at least 3 different width rear rims. 5, 7 and 8.5. Measure the distance from the center flange to the drop center edge (see picture) if it is about 1" you have 5 "wide rims if it is 3 you have 7 inch rims4-1/2 is 8.5 " wide rims. This assumes they all have the same Back set (1-3/8") I bet you have different wheels on your two tractors Pic one is a 5" rim the other 7" Last pic is 8.5" @sqrlgtr Did you see this? Thought you'd be interested. Share this post Link to post Share on other sites
Toolmanbill 47 #11 Posted yesterday at 11:30 AM One tire they were able to get the bead to seal but the other tire is not quite sealed.do you think it will seal with time?I put the tires on the tractor and they have not sealed yet.or should I just replace the tires and count as a loss?I really just don’t understand as both tractors had the same size factory tires.do you think it would help to run these over inflated or under inflated?I hope I don’t have to replace these as they were almost 300$. Share this post Link to post Share on other sites
953 nut 70,414 #12 Posted yesterday at 12:07 PM Did you sand off the rust and repaint the inside of your rims before having the new tires mounted? Share this post Link to post Share on other sites
Toolmanbill 47 #13 Posted yesterday at 12:21 PM The rims looked like new. 1 Share this post Link to post Share on other sites
953 nut 70,414 #14 Posted yesterday at 12:52 PM May ass well buy a tube. I have attempter overpressurizing tires and then hitting the rim all around with a plastic coated dead blow hammer and stopped the rim leak TEMPORARILY! I have used Bead Sealer which also didn't work but made a mess of the rim plus it cost as much as a tube. 1 Share this post Link to post Share on other sites
Toolmanbill 47 #15 Posted yesterday at 01:59 PM Put new tubes in.forgot to post that.still not sealed but they are holding air. Share this post Link to post Share on other sites
ebinmaine 81,176 #16 Posted 19 hours ago 9 hours ago, Toolmanbill said: holding air. That's what counts! I install tubes in ALL the tires we change or install new. Share this post Link to post Share on other sites
Toolmanbill 47 #17 Posted 6 hours ago I don’t know where to go from here.spent about 270$ on these tires +50$ for tubes.tires are still not sealed on the beads.did I just get bad install?used the tractor for leaf work about two hours and tires still didn’t seal.if I decide to just get a different tire what do I buy.this tractor had 23x9.5x12 tires originally and bought 23x8x12.do I go with 23x10.5x12?there doesn’t seem to be any of the original size with an aggressive tread design that I would like to have. Share this post Link to post Share on other sites
ebinmaine 81,176 #18 Posted 6 hours ago (edited) 4 minutes ago, Toolmanbill said: I don’t know where to go from here.spent about 270$ on these tires +50$ for tubes.tires are still not sealed on the beads.did I just get bad install?used the tractor for leaf work about two hours and tires still didn’t seal.if I decide to just get a different tire what do I buy.this tractor had 23x9.5x12 tires originally and bought 23x8x12.do I go with 23x10.5x12?there doesn’t seem to be any of the original size with an aggressive tread design that I would like to have. Can you post pics of what you got? And where they aren't sealing? If you're still having air leakage at this point then you have a bad tube. Not tire. Edited 6 hours ago by ebinmaine Correct autocorrect Share this post Link to post Share on other sites
pfrederi 21,314 #19 Posted 5 hours ago (edited) Have you measured you rims??? If you are trying to put 23 8.50 12s on 8.5 inch rims that will be an issue. tires need to be about 1.5" wider than the rims. You can mount wider tires on narrow rims but the tread may not lie flat on the pavement and they look bulgy... You keep listing your tire as 8 is it not an 8.50 Edited 5 hours ago by pfrederi Share this post Link to post Share on other sites
sqrlgtr 4,190 #20 Posted 4 hours ago (edited) All of my 300 series tractors had 7" wide rims and had either 23x9.50 turf's or 23x8.50 ag type tires. How much air have you put in trying to get them to seal? Soapy water is your friend also when getting the beads to pop out and seal. The Carlstar tire you have are a pretty respected tire if they are the Carlisle brand but I guess they still could have made some bad ones but doubt it. BTW I have used cheapo grease instead of soapy water but little harder to clean up. Edited 4 hours ago by sqrlgtr Share this post Link to post Share on other sites
Toolmanbill 47 #21 Posted 3 hours ago Filled tires up to 45 pounds.put soap on the bead area.will try to get pictures up today. 1 Share this post Link to post Share on other sites
oliver2-44 11,833 #22 Posted 3 hours ago Use them for a while, the tire bead should gradually work further on the rim. After that lower the pressure to maybe 15 and see how they do. Just my thoughts. 1 Share this post Link to post Share on other sites
Toolmanbill 47 #24 Posted 28 minutes ago The first picture is of tire not sealing.second picture is of the rim size where the tire is not sealed. The third picture is of my old tractor where the tires are sealed and there is no tube in.do you think I’m dealing with a defective tire or improper installation? 1 Share this post Link to post Share on other sites
ebinmaine 81,176 #25 Posted just now 26 minutes ago, Toolmanbill said: The first picture is of tire not sealing.second picture is of the rim size where the tire is not sealed. The third picture is of my old tractor where the tires are sealed and there is no tube in.do you think I’m dealing with a defective tire or improper installation? My first gut instinct would actually be lack of lubrication. I have had to squeeze the bead and the whole tire in onto the rim more than once, to get them to seat sometimes. I have also had to reapply a pretty loose mix of half water, half dish soap to get them to set. Last year I purchased actual tire lube for a few bucks and it helped substantially. Share this post Link to post Share on other sites