Toolmanbill 45 #1 Posted June 23 You guys helped me out last year about upgrading tires.lucky for me that I took your advice. I purchased carlstar all trail 23x8x12 tires. They worked unbelievably well. I have since purchased another wheel horse 314-8 and would like to upgrade the tires for this as well. I noticed on Amazon they have 23x10.5x12 tires from Hoosier wheel that look very similar. The carlstar are 272$ and the Hoosier tires are 161$.hate to cheap out but at 111$ difference it’s tempting. also had plans to attend the big show on Friday . But the forecast is likely looking like rain.Thursday looks much better.is there anything going on then or should I just go Friday and dodge the raindrops? Share this post Link to post Share on other sites
ebinmaine 81,158 #2 Posted June 23 2 hours ago, Toolmanbill said: The carlstar are 272$ and the Hoosier tires are 161$.hate to cheap out but at 111$ difference it’s ******. I've run tires of all grades, several brands and sizes. Are you planning on keeping this tractor? If you know what you got from the other set and that was pleasing, get them. If it's just for resell... maybe try the cheapos? Share this post Link to post Share on other sites
Handy Don 17,684 #3 Posted June 23 (edited) 2 hours ago, Toolmanbill said: also had plans to attend the big show on Friday . But the forecast is likely looking like rain.Thursday looks much better.is there anything going on then or should I just go Friday and dodge the raindrops? By Thursday afternoon, the show will be quite busy. Larger vendors will have had time to set up; many smaller ones as well. Busiest day is Friday, for sure. Weather at previous shows has included epic downpours, wilting heat, and strong winds. Come prepared and just go with it. Edited June 23 by Handy Don Share this post Link to post Share on other sites
rjg854 13,422 #4 Posted June 23 4 hours ago, Toolmanbill said: Amazon they have 23x10.5x12 tires from Hoosier wheel that look very similar. The carlstar are 272$ and the Hoosier tires are 161$. I'd go for the cheaper tire, if they are somewhat comparable, in ply rating, and you don't mind a wider tire. Share this post Link to post Share on other sites
pfrederi 21,312 #5 Posted June 23 Unless you are running a commercial lawn service with your WH I would bet any tire would dry rot/crack before you wore it out. 1 1 Share this post Link to post Share on other sites
Toolmanbill 45 #6 Posted yesterday at 11:50 AM Had so much luck buying these carlstar 23x8x12 tires I wanted to buy another set for this 2001 314-8 I purchased.took them to the local Goodyear store. They told me they couldn’t mount them without putting tubes in them.since I had these mounted on my 1994 model I just assumed that someone there didn’t know what they were doing.so I took them to the shop where I had the other ones mounted.he couldn’t mount them either.eventually had to put tubes in them as well.couldn’t find any information that wheel sizes had changed.any idea where I would find that info? Share this post Link to post Share on other sites
My_horse 139 #7 Posted yesterday at 01:19 PM 1 hour ago, Toolmanbill said: Had so much luck buying these carlstar 23x8x12 tires I wanted to buy another set for this 2001 314-8 I purchased.took them to the local Goodyear store. They told me they couldn’t mount them without putting tubes in them.since I had these mounted on my 1994 model I just assumed that someone there didn’t know what they were doing.so I took them to the shop where I had the other ones mounted.he couldn’t mount them either.eventually had to put tubes in them as well.couldn’t find any information that wheel sizes had changed.any idea where I would find that info? What was the reason that they couldn’t mount them? Couldn’t get the beads to seat/seal? Share this post Link to post Share on other sites
Toolmanbill 45 #8 Posted yesterday at 02:52 PM Yes.couldn’t get the beads to seal.what I saw was the tire was much narrower than the wheel. Share this post Link to post Share on other sites
pfrederi 21,312 #9 Posted 23 hours ago (edited) WH used at least 3 different width rear rims. 5, 7 and 8.5. Measure the distance from the center flange to the drop center edge (see picture) if it is about 1" you have 5 "wide rims if it is 3 you have 7 inch rims4-1/2 is 8.5 " wide rims. This assumes they all have the same Back set (1-3/8") I bet you have different wheels on your two tractors Pic one is a 5" rim the other 7" Last pic is 8.5" Edited 23 hours ago by pfrederi Share this post Link to post Share on other sites
cafoose 3,883 #10 Posted 20 hours ago 2 hours ago, pfrederi said: WH used at least 3 different width rear rims. 5, 7 and 8.5. Measure the distance from the center flange to the drop center edge (see picture) if it is about 1" you have 5 "wide rims if it is 3 you have 7 inch rims4-1/2 is 8.5 " wide rims. This assumes they all have the same Back set (1-3/8") I bet you have different wheels on your two tractors Pic one is a 5" rim the other 7" Last pic is 8.5" @sqrlgtr Did you see this? Thought you'd be interested. Share this post Link to post Share on other sites
Toolmanbill 45 #11 Posted 3 hours ago One tire they were able to get the bead to seal but the other tire is not quite sealed.do you think it will seal with time?I put the tires on the tractor and they have not sealed yet.or should I just replace the tires and count as a loss?I really just don’t understand as both tractors had the same size factory tires.do you think it would help to run these over inflated or under inflated?I hope I don’t have to replace these as they were almost 300$. Share this post Link to post Share on other sites
953 nut 70,374 #12 Posted 2 hours ago Did you sand off the rust and repaint the inside of your rims before having the new tires mounted? Share this post Link to post Share on other sites
Toolmanbill 45 #13 Posted 2 hours ago The rims looked like new. 1 Share this post Link to post Share on other sites
953 nut 70,374 #14 Posted 2 hours ago May ass well buy a tube. I have attempter overpressurizing tires and then hitting the rim all around with a plastic coated dead blow hammer and stopped the rim leak TEMPORARILY! I have used Bead Sealer which also didn't work but made a mess of the rim plus it cost as much as a tube. 1 Share this post Link to post Share on other sites
Toolmanbill 45 #15 Posted 59 minutes ago Put new tubes in.forgot to post that.still not sealed but they are holding air. Share this post Link to post Share on other sites