B-80 36" Deck Spindles Not Common?

[mas041 1]

I've been looking all over for just one deck spindle and side pulley after my spindle was bent or the bearing was shot. Either way, the actual spindle is damaged from removal. Pulley was rusted stuck so looking to replace that as well. I think its a 5-0621 deck but I'm not sure. The spindles don't quite line up with what I'm seeing online. 

 

Anybody got a spindle for this?

[ineedanother 2,062]

I don't have a replacement for that but you should put an ad in the wanted section of the classifieds. I'm sure someone here has one.

[gwest_ca-(File Mod) 12,166]

Welcome to Red Square

 

Mower spindle assemblies could be B, A1, G2 or Z

For A1 see service bulletin 292B

For G2 see service bulletin 292B

Click on the fuzzy picture in the link to download the 35 page manual

 

[BradKahler 297]

I believe this is the same shaft you're looking for, it is 4-1/2" long.  I received this from someone only to find out it was not a match for the shafts I was looking for.  The bearings are frozen but the shaft looks to be in ok condition.  You can have it for the cost of shipping if you think you can use it.  Shipping would be from Richmond KY.

 

 

 

 

 

[953 nut 65,325]

14 hours ago, mas041 said:

looking all over for just one deck spindle and side pulley after my spindle was bent or the bearing was shot. Either way, the actual spindle is damaged from removal. Pulley was rusted stuck so looking to replace that as well. I think its a 5-0621 deck but I'm not sure. The spindles don't quite line up with what I'm seeing online. 

Looks like @BradKahler has you covered on the spindle, what is the diameter of the pulley you need? A post in our free classified section may get the job done.  https://www.wheelhorseforum.com/classifieds/wanted/

[Brockport Bill 2,280]

check K&B parts listed here as Vendor on tool bar - they have spindles

[gwest_ca-(File Mod) 12,166]

You may want to replace with a newer version that uses blades with a 3/4" center hole. The D-hole blades are getting hard if not impossible to find.

[Lane Ranger 11,950]

11 minutes ago, gwest_ca said:

You may want to replace with a newer version that uses blades with a 3/4" center hole. The D-hole blades are getting hard if not impossible to find.

 

yes if the deck is still strong than moving to the upgraded spindle setup is a very good idea! 

[mas041 1]

9 hours ago, BradKahler said:

I believe this is the same shaft you're looking for, it is 4-1/2" long.  I received this from someone only to find out it was not a match for the shafts I was looking for.  The bearings are frozen but the shaft looks to be in ok condition.  You can have it for the cost of shipping if you think you can use it.  Shipping would be from Richmond KY.

 

 

 

 

 

Sounds good Brad, I live in Richmond Va, so it's going from Richmond to the Richmond ha. I'll send you a PM to get the shipping set up.

[mas041 1]

7 hours ago, 953 nut said:

Looks like @BradKahler has you covered on the spindle, what is the diameter of the pulley you need? A post in our free classified section may get the job done.  https://www.wheelhorseforum.com/classifieds/wanted/

The pulley is roughly 3.25 inches in diameter. I'll check the classifieds

[76c12091520h 4,133]

4 hours ago, mas041 said:

Sounds good Brad, I live in Richmond Va, so it's going from Richmond to the Richmond ha. I'll send you a PM to get the shipping set up.

Those shafts and bearings ( #103119 ) are all one piece , they are pressed into the housing.

[76c12091520h 4,133]

8 hours ago, Brockport Bill said:

check K&B parts listed here as Vendor on tool bar - they have spindles

We do !